Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Pay attention to agitation. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. GB-9 SGCZ2600DL/SGCZ2600DW 8. Operation STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube. 3. Move the choke lever to the closed position. IMPORTANT Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 7. Move the choke lever downward to open the choke. And restart the engine. 8. Allow the engine to warm up for a several minutes before starting operation. NOTE 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. STOPPING ENGINE 1. Release the throttle trigger and run the engine for a half minute. 2. Shift the stop switch to the “Stop” position. IMPORTANT choke lever close open [SGCZ2600DL] [SGCZ2600DW] 1 2 3 (1) (1) (1) Stop switch 4. [SGCZ2600DL] Set the stop switch to the “-” position. Set the throttle trigger to the start position (1 > 2 > 3). Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. [SGCZ2600DW] Set the stop switch to the “RUN” position. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. 5. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. 6. While holding the unit firmly, pull out the starter rope quickly. Except for an emergency, avoid stopping the engine while pulling the throttle trigger. ADJUSTING THROTTLE CABLE The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. 1 to 2mm ( 04in ) ADJUSTING IDLING SPEED 1. When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise. 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise. Cable adjuster Idle adjusting screw NOTE Warm up the engine before adjusting the idling speed. GB-10 SGCZ2600DL/SGCZ2600DW 8. Operation HARNESS WARNING ALWAYS WEAR THE PROVIDED HARNESS WHEN USING THE MACHINE! Always make sure the machine is hooked securely to the harness. If you don't, you will be unable to control the machine safely.This can result in injury to yourself or others. Never use a harness with a defective quick release or any other damage. HOW TO WEAR 1. Wear the provided harness without twisted bands, with the hanger on your right side. (1) (DL: Single strap) (DW: Double strap) (1) Hanger (1) BALANCE THE UNIT 1. Hook your machine to the hanger. 2. Adjust the bands of the harness to have the blade parallel to the ground when standing in your normal working position to provide you most effectiveness and comfort on operating the machine. 3. In order to prevent the hanger position to change during operation, turn up the extra part of the band from the buckle. 4. When correctly adjusted, check the correct working of the harnesses' QUICK RELEASE. QUICK RELEASE The harness is equipped with a "QUICK RELEASE"devise. To release the machine from the harness in emergency situations, please follow the procedure as explained below. WARNING Make sure to check proper working of the QUICK RELEASE device BEFORE operating the machine. Make sure to hold the unit securely when using the QUICK RELEASE. (DL) While holding the unit by your right hand securely, press both sides of the buckle. sides of the buckle. (1) Buckle (1) (DL: Single strap) NOTE a) Avoid running the engine at full throttle with no load. Continuous no load full throttle operation can cause damage to the engine and the drive shaft. b) Operation at too slow engine speed can cause abnormal vibration of the machine, resulting in short life of drive shaft and clutch parts. If you felt such vibration, use a higher speed range. c) Though the blades are made of steel harder than conventional metal blades, continuous cutting in soil will accelerate wear. GB-11 (DW) While holding the unit by your left hand securely, press the red button of the buckle. Then take the harness off from your shoulders. (1) G B (1) Buckle (DW: Double strap) USAGE This machine does cutting not by a rotary cutter like conventional trimmers but by a pair of special blades, each upper blade and lower blade oscillate opposite direction alternately within a limited angle at a speed of approximately 1/30 of conventional trimmers. This unique mechanism brings you many benefits like the following: 1. Since the blade does not cause grass chips and pebbles to t...
Este manual também é adequado para os modelos :Jig Saw e - SGCZ2600DW (788.45 kb)