Replacement blades for this saw are available from your nearest Ryobi dealer. Page 6 OPERATION OPERATION TO INSTALL BLADES See Figure 3. ¦ UNPLUG YOUR SAW. WARNING: Failure to unplug your saw could result in accidental starting causing serious injury. ¦ Remove the 5/32 in. allen wrench provided with this saw from allen wrench holder. NOTE: Allen wrench holder is located in bottom portion of saw handle. See Figure 1. ¦ Loosen the blade clamp screw enough to permit the saw blade to be inserted bet

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this operator's manual. ¦ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. ¦ DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol, or any medication. ¦ CUTTING INTO ELECTRICAL WIRING IN WALLS AND FLOORS CAN CAUSE THE BLADE AND METAL PARTS TO BECOME

PARTS LIST Key Part No. Number Description Quan. Key Part No. Number Description Quan. 1 990496-016 Cord .................................................................... 1 2 968775-001 Screw (M3 x 7 Fil. Hd.) ....................................... 2 3 617966-028 Screw (#8-10 x 1/2 in. Pan Hd.) ......................... 1 4 617966-030 Screw (#8-10 x 5/8 in. Pan Hd.) ....................... 10 5 973703-001 Logo Plate .......................................................... 1 6 617966-032 Sc

When properly connected, red light will turn on. ¦ Normally, the yellow and green lights on the charger will come on. This indicates charger is in control charge mode and should switch to fast charge mode within 5 minutes. When charger is in fast charge mode the red light will come on. If after a period of 15 minutes the yellow and green lights remain on, remove the battery pack, wait 1 minute and reinsert battery pack in charger. If the yellow and green lights continue to remain on an additiona

All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal wiring. Observe all normal safety pre- cautions to avoid electrical shock. Important: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qual

ASSEMBLY UNPACKING This product has been shipped completely assembled. nCarefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. nInspect the tool carefully to make sure no breakage or damage occurred during shipping. nDo not discard the packing material until you have carefully inspected and satisfactorily operated the tool. nIf any parts are damaged or missing, please call1-800-525-2579 for assistance. PACKING LIST Reciprocat

WARNING: Do not allow familiarity with your circular saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. OPERATION OPERATION LED FUNCTION OF CHARGER 1400667 See Figure 2. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ¦ Red LED Lighted = Fast Charging Mode. ¦ Green LED Lighted = Slow Charging Mode and Fully Charged Battery Pack. ¦ Yellow and Green LED Lighted = Soft Start Mode, or After 1/2 Hour Equals Hot or Defect

n Green LED on = Fully charged and in maintenance charge mode. n Green LED on = When battery pack is inserted intocharger, indicates hot battery pack or that battery pack is out of or below normal temperature range. n Yellow and Green LEDs on = Deeply discharged ordefective battery pack. n No LED on = Defective charger or battery pack. CHARGING THE BATTERY PACK Battery packs for this tool have been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it un

or 1-800-265-6778 in Canada SAVE THIS MANUAL FOR FUTURE REFERENCE SPECIFICATIONS: Length of stroke 1 in. (25.4mm) Strokes per minute 0-2000 spm Length (without blade) 17 in. (430 mm) Engine Type Air Cooled 2 Cycle Gasoline Engine Displacement 15.9 cc Starting System Recoil Carburetor Diaphram Fuel Tank Capacity 0.35 literes Net weight 11 lbs. STOP TABLE OF CONTENTS TABLE OF CONTENTS ¦ Table of Contents ..............................................................................................

A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately. n Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately. n Do not charge battery tool in a damp or wetlocation. Following this rule will r