Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Pull the cap to remove it. Oil filler cap installation (Lock): Insert the oil filler cap into the oil filler port with the lug being set horizontally. Turn the oil filler cap 90° clockwise so the lug of the cap is in line with the rib of the alternator cover. (It should click.) 1. 2. 3. 4. 5. 6. 1) 2) 2) 84 1) 88 SERVICING YOUR OUTBOARD MOTO R Engine Oil Change An engine oil evacuation device may be used to remove the engine oil. Drain the used oil while the engine is warm. Warm oil drains quickly and completely. 1. Unlock and remove the engine cover (p. 84 ). DRAIN BOLT GUIDE SEALING WASHER 2. Place a suitable container below the oil drain guide to catch the used oil, and then remove the oil filler cap (p. 85 ) and the drain bolt. 3. Allow the used oil to drain completely. Use a new sealing washer, and then reinstall the engine oil drain bolt and washer. Tighten the drain bolt securely. Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not throw it in the trash, pour it on the ground or downadrain. SERVICING YOUR OUTBOARD MOTOR 4. With the outboard motor in a vertical position, fill to the upper limit mark on the dipstick (p. 85) with the recommended oil. Engine oil refill capacity: Without oil filter change: 4.4 US qt (4.2 L) With oil filter change: 4.6 US qt (4.4 L) 5. Install the oil filler cap and tighten it securely (p. 85 ). 6. Install and lock the engine cover. Oil Filter Change 1. Drain the engine oil, and reinstall the drain bolt (see Engine Oil Change on p. 86). 2. Tilt the outboard motor, and place a suitable container below the oil drain guide to catch the used oil. 3. Use a suitable tool to remove the oil filter, and thoroughly drain the filter into the used oil container. FILTER WRENCH, 64 mm OIL FILTER OIL DRAIN GUIDE RUBBER SEAL SERVICING YOUR OUTBOARD MOTOR 4. Clean the oil filter mounting base, and coat the rubber seal of the new oil filter with clean engine oil. Use only a Honda Genuine oil f ilter or a f ilter of equivalent quality specif ied f or your model. Using the wrong f ilter, or a non- Honda f ilter which is not of equivalent quality, may cause engine damage. 5. Screw on the new filter by hand until it contacts the engine, then use a suitable tool to tighten the filter an additional 7/8 turn. OIL FILTER TIGHTENING TORQUE: 9 lbf·ft (12 N·m , 1.2 kgf·m) 6. Return the outboard motor to the vertical position, and fill the crankcase with the specified amount of the recommended oil. 7. Start the engine and check for leaks (be sure the water level is at least 2 inches above the antiventilation plate). If you are changing the oil filter while the outboard motor is out of the water, use commercially available Ear-muffs and water hose to supply water. Running the outboard motor without sufficient cooling water will damage the water pump and overheat the engine. 8. Stop the engine, and check the oil level as described on page 85 . If necessary, add oil to bring the oil level to the upper limit mark on the dipstick. Engine Oil Recommendations Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. SAE Viscosity Grade AMBIENT TEMPERATURE SAE 10W-30 is recommended for general use. Honda recommends that you use API service category SG, SH or SJ oil with the ‘‘starburst’’ certification mark. The SAE oil viscosity and service category are in the API label on the oil container. Suggested oil: Honda 10W-30 FC-W TM outboard motor oil is suggested for general use. .. .. .. IZFR6K-11E (NGK) 89 Spark Plug Service SERVICING YOUR OUTBOARD MOTOR PLUG MAINTENANCE COVER 6 20mm FLANGE SH BOLT Incorrect spark plugs can cause engine damage. RECOMMENDED SPARK PLUGS: Do not adjust the spark plug gap. If the gap is out of specification, replace the spark plug with a new one. Disconnect the battery negative ( ) terminal. Unlock and remove the engine This outboard motor uses spark plugs cover (p. ). that have an iridium coated center electrode. Be sure to observe the following when servicing the spark plugs. Do not clean the spark plugs. If an electrode is contaminated with accumulated objects or dirt, replace the spark plug with a new one. Use only a ‘‘wire-type feeler gauge’’ to check the spark plug gap if necessary. To prevent damaging the iridium coating of the center electrode, never use a ‘‘leaf-type feeler gauge.’’ Remove the 6 20 mm flange SH bolt and remove the plug maintenance cover. 1. 2. 84 3. .. .. .. .. .. .. 90 SERVICING YOUR OUTBOARD MOTOR CONNECTOR LOCK TAB IGNITION COIL PLUGWRENCH BOXWRENCH SEALINGWASHER INSULATOR 6 25mm FLANGE BOLT 0.039 0.051 in (1.0 1.3 mm) Remove the 6 25 mm flange bolt. Disconnect the connector by pushing the lock tab and remove the ignition coil. Remove the spark plug using the plug wrench, box wrench and the Phillips /flat-tip screwdrivers (accessories). Inspect the spark plug...
Este manual também é adequado para os modelos :Barcos - Outdoor Motor BF75D (4.54 mb)