Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
• Ask your dealer for the output power level for each selection. TALK AROUND KEY . Push to turn the talk around function OFF. . Push and hold to turn the talk around function ON. • The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY . Push to select the IF bandwidth to wide. • The wide passband width can be selected from 25.0 or 20.0 kHz using the CS-F14 CLONING SOFTWARE. (PMR operation only) Ask your dealer for details. . Push and hold to select the IF bandwidth to narrow. 10 PANEL DESCRIPTION 2 DTMF AUTODIAL KEY Push to transmit code. CALL KEYS Push to transmit a 2/5- • Call transmission is necessary on your signalling system. • [Call A] and/or [Call B] keys may be available when your selective ‘ Individual/Group’ calls. Ask your dealer which call is assigned to each key. EMERGENCY KEYS . Push and hold to transmit an emergency call. . When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted without beep emission. • If you want to cancel the emergency call, push (or push and the key again before transmitting the call. • The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. VOICE SCRAMBLER FUNCTION KEYS . Push to turn the voice scrambler function OFF. . Push and hold to turn the voice scrambler function ON. OPT OUT KEYS . Push to inactivate the connected output signal level. . Push and hold to activate the connected output signal level. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example. 13 CONVENTIONAL OPERATION 3 3 12 3 CONVENTIONAL OPERATION Turning power ON . Rotate [VOL] to turn power ON. Channel selection IC-F14S/F24S: Toggle [CHANNEL SWITCH] to select the channel 1 or 2, or, push one of [MRCH 1] to [MR-CH 4] key to select a channel directly. • The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned. IC-F14/F24: Rotate [CHANNEL SELECTOR] to select the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel directly. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. [VOL] [CHANNEL SELECTOR] [CHANNEL SWITCH] Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operator’s instructions. • This may not be necessary depending on programming. w Push the call key (assigned to one of the dealer programmable keys.) (p. 11) eAfter transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling 3 Receiving NOTE: Transmitting without See p. 2 for antenna attachment. Receiving: q Rotate [VOL] to turn power ON. w Toggle [CHANNEL SWITCH] (IC-F14S/F24S), rotate [CHANNEL SELECTOR] (IC-F14/F24) or push one of [MR-CH 1] to [MR-CH 4] key to select a channel. For IC-F14S/F24S: The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned. e When receiving a call, adjust the audio output level listening level. Transmitting: Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT] , speak into the microphone at a normal voice level. • When a tone signalling system is used, the call procedure described on p. 13 may be necessary. w Release [PTT] to return to receive. IMPORTANT!: To maximize the readability of your signal; 1. Pause briefly after pushing [PTT] . 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. CONVENTIONAL OPERATION 3 D Transmitting notes • Transmit inhibit function The transceiver has several under the following - The channel is in mute condition. - Channel is busy. - Un-matched (or matched) CTCSS is - The selected channel is a ‘ receive only’ channel. • Time-out timer After continuous transmission for the pre-programmed time-out timer activates, and causes the transceiver • Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer. D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. . Push [DTMF Autodial] to transmit the DTMF code. 3 3 3 Scrambler The optional voice 109 (#01) and UT-110 (#01) provide high performance with the same scrambler . Push and hold [Scrambler] to turn the scrambler function ON. . Pu...
Este manual também é adequado para os modelos :equipamento de barco - IC-F14/S (802.57 kb)