Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
• IC-F14/F24 : Rotate the channel selector to select the pre-programmed memory channels. w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjust the audio level. PANEL DESCRIPTION 2 e LED INDICATOR (p. 8) . Lights red while transmitting. . Lights green while receiving open. . Lights/blinks orange when the according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone. [SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional speak-er-microphone is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower] The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT] Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. D DD Programmable key reference Upper Lower 2 2 ‘ ‘‘ LED indicator The LED indicator as follows; (Ref.; R=Red, G=Green, • TX: Turns Red while transmitting a signal. R • RX: Turns Green while receiving a signal. G • Call LED (ON): When receiving a matched 2/5-tone. O O • Call LED (Blink): When receiving a matched 2/5-tone. O O • Fast/Slow scan: Blinks while Fast/Slow scan is activated. G G • Low BATT1: You should charge the battery. (blinks slowly) G G • Low BATT2: You must charge the battery. (blinks fast) G G G G • TX low BATT2: Low BATT2 was detected during TX mode. R R R R • CH err: Non-programmed channel is selected. R O R O R O R O R O R O R O R O 2PANEL DESCRIPTION ‘ ‘‘ Programmable The following functions [Upper] and [Lower] programmable function Consult your Icom dealer your transceivers programming. If the programmable function names explanations, the specific key used to activate the function on programming. SCAN A KEY . This key’s operation depends on the Power ON Scan When the power ON scan function is turned Push to start and cancel scanning operation. In case during scan, cancels scanning. When the power ON scan function is turned ON; Push to pause scanning. Scanning resumes after passing specified time period. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specified time period. SCAN B KEY Push to start and cancel scanning operation. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specified time period. PRIORITY CHANNEL KEYS . Push to select the Priority A or Priority B channel. . Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel. MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. NOTE: The memory channels 3 and 4 are available for ICF14S/ F24S when [MR-CH 3] and [MR-CH 4] keys are assigned. 9 2 2 PANEL DESCRIPTION MONITOR KEY . Mute and release Open any squelch/(LMR operation only) . Activates one of (or two independently: (PMR operation only) • Push and hold to un-mute the channel ‘ Audible’ condition). • Push to mute the channel (sets to ‘ Inaudible’ only). • Push to un-mute the channel (sets to ‘ Audible’ only). • Push after the communication is finished to send a ‘ reset code’ . NOTE: The un-mute condition ( ‘ Audible’ condition) may automatically return to the mute condition ( ‘ Inaudible‘ condition) after a specified period. LOCK KEY Push and hold to electronically lock all programmable keys the following: [Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys. OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, depending on the pre-setting. • Ask your dealer for the output power level for each selection. TALK AROUND KEY . Push to turn the talk around function OFF. . Push and hold to turn the talk around function ON. • The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY . Push to select the IF bandwidth to wide. • The wide passband width can be selected from 25.0 or 20.0 kHz using the CS-F14 CLONING SOFTWARE. (PMR operation only) Ask your dealer for details. . Push and hold to select the IF bandwidth to narrow. 10 PANEL DESCRIPTION 2 DTMF AUTODIAL KEY Push to transmit code. CALL KEYS Push to transmit a 2/5- • Call transmission is necessary on your signalling system. • [Call A] and/or [Call B] keys may be available when your selective ‘ Individual/Group’ calls. Ask your dealer which call is assigned to each key. EMERGENCY KEYS . Push and hold to transmit an emergency call. . When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted without beep emission. • If you want to cancel the emergency call, push (or push and the key again before transmitting the call. • The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. VOICE SCRAMBLER FUNCTION KEYS . Push to turn the voice scrambler function OFF. . Push and hold to turn the voice scrambler function ON. OPT OUT KEYS . Push to inactivate the co...
Este manual também é adequado para os modelos :equipamento de barco - IC-F24/S (802.57 kb)