Assessments - 2, GPA: 5 ( )

Fabricante : Desa Arquivo Tamanho: 3.76 mb Arquivo Nome : Língua de Ensino:

If you smell gas, STOP! See Safety Information, page 2. If you don’t smell gas, go to the next step. 5. Turn control knob counterclockwise to the PILOT position and press in. Keep control knob pressed in for five (5) seconds. Note:You may be running this log set for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system. • If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs. 6. With control knob pressed in, push down and release ignitor button. This will light pilot. Visually locate the pilot on the control valve cover by the edge of the burner pan to look for flame. If needed, keep pressing ignitor button until pilot lights. Note: If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier. 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note:If pilot goes out, repeat steps 3 through 7. 8. Turn control knob counterclockwise to the ON position. Burner should light. If burner does not light, call a qualified service person. Control Knob Pilot Ignitor FROM "PILOT" POSITIONSLIGHT PUSH TOTURN OFFPULL PUSHON ONFROM "PILOT" POSITIONSLIGHT PUSH TOTURN OFFPULL PUSHFROM "PILOT" POSITIONSLIGHT PUSH TOTURN OFFPULL PUSHONOFF OFF OFFOn Off Figure 15 - Ignitor and Control Knob Pilot Burner Thermocouple Figure 16 - Thermocouple and Pilot For more information, visit more information, visit 901268-01D 901268-01D 10 Forr morre iinfforrmattiion,, viisiitt Pilot Thermocouple INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. The pilot is located on the back right hand side of the burner. The thermocouple should be fully enveloped in the flame. The flame should not be lifting off of the thermocouple element. If your pilot assembly does not meet these requirements: • Access the pilot adjustment screw through slot in valve cover. Turn adjustment screw clockwise to decrease or counterclockwise to increase the flame to proper size (see Figure 11, page 7). Do not remove the adjustment screw. • see Troubleshooting, pages 11 through 13 Figure 17 - Correct Pilot Flame Pattern Figure 18 - Typical Flame Pattern BURNER FLAME PATTERN Burner flames will be steady; not lifting or floating. Flames should go up through the middle of logset. Flames should not "spill" to the edges of the pan or sides of the logset. Figure 18 shows a typical flame pattern. If burner flame pattern differs from that described: • turn appliance off (see To Turn Off Gas to Appliance) • see Troubleshooting, pages 11 through 13 OPERATING APPLIANCE To Turn Off Gas To Appliance INSPECTING BURNERS Pilot Assembly Burner Flame Pattern CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE • Keep the area around the log set clean and clear of debris. • Occasionally, you may use a soft bristle brush to clean logs. • Periodically inspect the air mixer and burner tube for foreign matter blocking the air inlet and flame holes. • Once every year a qualified agency or certified chimney sweep should examine and clean the venting system of the fireplace. TO TURN OFF GAS TO APPLIANCE Shutting Off Appliance 1. Turn control knob clockwise to the PILOT position. 2. Press in and turn control clockwise to the OFF position. Shutting Off Burner Only (pilot stays lit) Turn control knob clockwise to the PILOT position. OPERATING APPLIANCE Continued TROUBLESHOOTING 11 TROUBLESHOOTING Note: For additional help, visit DESA International’s technical WARNING: Turn off log set and let cool before service web site at servicing. Only a qualified service person should Note: All troubleshooti...

Baixe o seu

Para fazer o download, introduza 2 dígitos :