SafetyAlertUseofthisproductisnotintendedto,anddoesnot,ensurethatmotoristsorpassengerswillnotbeinvolvedintrafficaccidents.ItisonlyintendedtoalertthemotoristthatanemergencyvehicleequippedwithaCobraSafetyAlerttransmitteriswithinrangeasdefinedbythatproduct.Pleasecalllocalfireandpolicedepartmentstolearnifcoverageexistsinyourarea. SafeDrivingMotorists,aswellasoperatorsofemergencyorservicevehicles,areexpectedtoexerciseallduecautionwhileusingthisproduct,andtoobeyallapplicabletrafficlaws. SecurityofYourV

pipe or 1/2 inch copper sweat connections. If the Moen Slip Fit spout is used, a 1/2 inch copper drop and lookout may be used. Measurements These are shown in the drawings. The depth measurement is critical. Use the front face of the plaster ground as a reference point for the finished wall position, including tile ( 1-3/4"[44mm] ). The supply piping centerline should be a maxium of 2" (51mm) and a minimum of 1" (25mm) behind the wall surface. Use thick wall handle extension kit 96945 for wall t

If the retainer clip is not properly installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the premises could result. Visit Moen's Web Site at WITH STOPS WITHOUT STOPS Stop Operation CC -This type is integral with casting, actuated by screwdriver, and require a 90° turn to open or close. When the screwdriver slot is vertical, the rubber stop is closed, and when the slot is horizontal, the rubber stop is open. IPS -This type has been added to t

Secure all pipes and the shower and tub drop ells. Use thread seal tape on all threads. Flushing IMPORTANT: Before closing all wall openings, pressure test valve and complete sys- tem using flushing instructions Pipe chips, sand and other solids found in new and renovated plumbing can damage the sealing surfaces of the cartridge causing a leak or cause the spool to become blocked. To avoid damage, DO NOT TURN ON SUPPLY VALVES until instructed below. Make sure both hot and cold supplies are off.

1. Rotate the handle counterclockwise to the stop, let the water run for several minutes to purge cool water from the hot water supply line, check the hot water temperature. 2. Rotate handle clockwise to off. Remove handle parts, see "Disassembly" and temperature limit stop, rotate the stop clockwise to decrease (counterclockwise to increase) maximum hot water temperature and reinstall into key stop. 3. For handle styles A & B replace handle, for style C replace handle adapter, do not use handle

Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer. (Note: The internal tooth washer is supplied with the TMB-S.) Internal tooth washer TMB-S bracket Bolt Nut Flat washer Attach motor mounting bracket to transducer. 2. Slide the adjustable strap supplied with the TMB-S through the slot in the transducer bracket and wrap it around the trolling motor. Position the transducer to aim straight down when the motor is in

NOTE: For optimum operation, the portable transducer should be adjusted so that it is parallel to the ground. For more information on this, see the earlier segment on Transducer Orientation and Fish Arches. 29 Operation KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unit has accepted a command. Numbers in the following photos correspond to key explanations in the following pages.: 4 2 3 1 1 2 3 4 Cuda 128 and Cuda 168EX Sonars, front view, each showing screen a

It’s ideal for snowmobile, camping, motorcycle and boat trailers. The Submersible Trailer Lighting Kit’s design conforms to applicable U.S. FMVSS 108 and Canadian CMVSS safety standards. Designed for 12 Volt Systems. KIT INCLUDES: (2) Eight function red stop/tail/turn lights • (1) Right/Curb side light (green/brown wires) • (1) Left/Road side light (yellow/brown wires and license plate illuminator) (1) License plate bracket (1) 25' (7.6 m) Wiring harness • (1) Short piece (for towing vehicle wir

The control mode options include factory selected combinations of ON/ OFF, time proportioning, PI using manual reset and full PID. Input for the Series 160 is a relative humidity/ temperature sensor. Features include mechanical relay outputs, remote setpot, optional remote digital displays, and various cable lengths to accommodate remote sensor location. The Series 160 is also available as a RH/Temperature signal conditioner only, that can be interfaced to other Watlow controls. Specifications

128, Cuda. 128 Portable, Cuda. 168, Cuda. 168EX Fish-finding & Depth Sounding Sonars Installation and Operation Instructions Copyright © 2002 Eagle Electronics All rights reserved. Eagle® is a registered trademark of Eagle Electronics Marine-Tex. is a trademark of Illinois Tool Works Inc. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to chang