Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Rear panel 12 10 10 9, 11 Display window The receiver and the DVD player use the same design for their display windows. 10 11 12 13 7 8 15, 18 18 4342 5 The numbers refer to the pages in which the parts are explained. If the effective distance between the remote control and remote control sensor on the receiver or the DVD player decreases, replace the batteries. Use two R6P (SUM-3)/AA(15F) type dry-cell batteries. CAUTION • Do not use a used battery and a new battery together. • Do not use different types of batteries at the same time. • Take out the batteries if the remote control is not to be used for a long time. Otherwise it may cause a leakage. Remote control operation When operating the remote control, point it at the front panel of the receiver or the DVD player. If the remote control is operated from a direction that is extremely oblique or when there is an obstacle in the way, signals may not be transmitted. If the remote control sensor is exposed to a strong light such as direct sunlight, correct operation may not be carried out. 14 6, 14 41 14 16 17 20 24 32 35 42 16 16 6 6 16 27 11 13 33 25 16 23 20 18 20 6 6 24, 25 23 27 27, 32 36 32 38 22 34 35 33 28, 30 30 15, 43 18 19 15, 21, 27, 36 21, 25, 34 15, 31, 43 Inserting batteries into the remote control Batteries (2) Using the remote control 24, 25 11, 17 24, 25 24, 25 6, 15, 23 15, 29, 44 Operating the TV using the remote control Operating the TV usingthe remote control You can operate your TV using the remote control of this system. Remote control mode selector F TV TV/VIDEO TV TV CHANNEL VOLUME ENTER Number buttons Setting the manufacturer code 1 Slide the remote control mode selector to TV. 2 Hold down F TV. • Hold down F TV until you finish step 4. 3 Press ENTER and release. 4 Press number buttons (1-9, 0). • Refer to “Using the number buttons” (A page 15). Examples: For a Hitachi TV: Press 1, then 0. For a Toshiba TV: Press 0, then 8. When the manufacturer of your TV has two or more codes, select the manufacturer codes in turn and find the one that operates the TV and the remote control properly. Manufacturer Code Manufacturer Code JVC 01 Samsung 12 Hitachi 10 Sanyo 13 Magnavox 02 Sharp 06 Mitsubishi 03 Sony 07 Panasonic 04, 11 Toshiba 08 Philips 14 Zenith 09 RCA 05 NOTE • A manufacturer code is subject to change without notice. You may not be able to operate the TV produced by the manufacturer. 5 Release F TV. Using the remote control for the TV operation Operate the remote control by pointing it at the TV. Turns on/off the TV. Changes the channels. Adjusts the volume. / ~ / *1 Selects the channels. Switches the previously selected channel and the current channel. Switches the TV and video input. *1 Make sure to slide the remote control mode selector to TV in advance. NOTE • After replacing the batteries of the remote control, set the manufacturer code again. • When the remote control mode selector is slid to TV, some buttons may not work. Introduction Connections Do not turn on the power until you complete the connection. Standard setup Speaker Receiver Speaker DVD player Connecting the antennas Connecting the AM loop antenna (supplied) 1 Set up the AM loop antenna. 2 Connect the antenna cord. Receiver (rear panel) 3 Turn the AM loop antenna to find the best position for radio reception. Place the AM loop antenna as far from the receiver as possible. • Do not place the AM loop antenna on a metallic table or close to a TV, computer, or other electric appliances. Doing so may affect radio reception. 7 When radio reception with the supplied AM loop antenna is poor Electric wire: 3 - 5 m (not supplied) Connect the ends of the antenna cord as shown above. If insulation covers the tips of the antenna cord, twist and pull off the insulation. White Black When positioning the antennas, find the best position for reception while listening to an actual radio program (refer to “Listening to radio broadcasts” (Apage 18)). Stretch out the electric wire horizontally, preferably in a high place such as above a window or outdoors. Connect the AM loop antenna cord to the receiver together with the electric wire. Receiver (rear panel) AM loopantenna cord Electric wire Twist together electric wire and the AM loop antenna cord. Connecting the FM antenna (supplied) Receiver (rear panel) FM antenna Stretch out the FM antenna to the best position for radio reception, and then fix the FM antenna with adhesive tape. 7 When radio reception with the supplied FM antenna is poor, or when using a communal antenna Antenna cord (not supplied) Outdoor FM antenna (not supplied) Converter (not supplied: compatible with 300 C/75 C) Coaxial cord (not supplied) Depending on the radio reception conditions, an FM feeder antenna (not supplied: compatible with 300 C) can be used. In this case, a converter (not supplied) is required. or Communal antenna terminal Receiver (rear panel) When using an antenna other than those supplied with this system, refer to the operation manuals for...