Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
7 77 UK INTRODUCTION To get the best out of your new appliance, please read this user guide carefully before using it for the first time. Take particular note of the safety precautions. We also recommend that you keep the instructions for future reference, so that you can remind yourself of the functions of your appliance. IMPORTANT SAFETY PRECAUTIONS General • Incorrect use of this appliance may cause personal injury and damage. • Use for its intended purpose only. The manufacturer is not responsible for any injury or damage resulting from incorrect use or handling (see also Guarantee Terms). • For domestic use only. Not for outdoor or commercial use. • Only connect the adapter cord to 2 0 V, 50 Hz. • Do not immerse the appliance, cord or adapter in water or any other liquid and make sure no water enters the appliance. • This symbol [] means that the appliance cannot be used in the bath tub or near water, wash basins, bowls or the like. • We recommend you only use this appliance if the installation is protected by an HFI-/HPFI relay. Please contact a qualified electrician if in doubt. • Always disconnect from the mains and switch off the appliance at the on/off switch before cleaning. • Be careful with the cutting head when cleaning or lubricating it, as it is very sharp. • Never leave unattended when in use, and keep an eye on children. • Do not expose to direct sunlight, high temperatures, humidity, dust or corrosive substances. • Only use the appliance in ambient temperatures of 10-40°C. Avoid exposing the appliance to temperatures below -10°C or above +40°C for an extended period of time. • Do not use if the cutting head is damaged, as it may cut the skin. • Check regularly that neither the cord nor the adapter is damaged and do not use if there is any damage, or if it has been dropped on the floor, dropped in water or damaged in any other way. • If the appliance, cord or adapter has been damaged, have the appliance inspected and if necessary repaired by an authorised repairer. Never try to repair the appliance yourself. Please contact the store where you bought the appliance for repairs under the guarantee. Unauthorised repairs or modifications to the appliance will invalidate the guarantee. 8 88 KEY TO THE MAIN COMPONENTS OF Fitting the comb attachment THE APPLIANCE . Adapter with cord 2. Charger jack 3. Comb 4. Scissors 5. Holder 6. Lubricating oil 7. Cleaning brush 8. Cutting head 9. Locking ring 10. On/Off button . Recharging indicator 12. Charger jack . Large comb, 4, 7, 0, 2 and 6 mm 4. Fine comb, and mm Symbols on locking ring Unlocked symbol Locked symbol Thinning symbol PRIOR TO FIRST USE Before using for the first time, fully charge the battery (See Battery Charging below), which takes approx. 8-12 hours. USING THE APPLIANCE The appliance is designed for cutting and trimming of hair and beard and can be used with or without a comb attachment, depending on the required length. • Fit the required comb attachment ( or 4): o Set the locking ring (9) so the unlocked symbol is level with the arrow on the appliance. o Place the desired comb attachment over the cutting head (8) so the small pins on either side of the cutting head click into place in the small indentations on either side of the comb attachment. o Remove the comb attachment by carefully pulling it away. The locking ring must be unlocked. • Set the comb attachment to the desired cutting length by sliding it up and down the appliance until the arrow on the appliance is level with the desired length. o The small comb attachment can be set to lengths of or mm and the large comb attachment can be set at 4, 7, 0, 2, 4 or 6 mm. • Lock the locking ring by turning it until the locking symbol is level with the arrow on the appliance. • Switch on the appliance using the on/off button (10) and commence trimming. Trimming and shaving without a comb attachment The cutting head is used to trim the beard and shave the head, e.g. in the neck. Carefully slide the appliance over the skin with slow even movements at a low angle and without using pressure. • Take care not to push in the direction of the cutting head or to push the cutting head sideways. • Caution! The cutting head is very sharp, so be careful! Trimming with a comb attachment Trim the beard by using the appliance with a decreasing cutting length until the beard has the desired length. 9 99 Thinning with a comb attachment Set the locking ring so the thinning symbol is level with the arrow on the appliance. Thin the hair or the beard by cutting against the growth direction of the hair. Tips • Check the required comb attachment is fitted and set to required length. • Only cut small lengths of hair at a time. Use decreasing settings until you achieve the right length. o The cutting head will slow down or become blocked if the speed is too fast or if you cut too much hair at a time. • Hold the appliance with the slanting side of the comb attachment facing the head, and move in slow, even moveme...