Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate appliance when you are tired. • REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual should be performed by Black & Decker Authorized service organizations, • USE OF ACCESSORIES The use of any accessory or attachment not appliance could be hazardous. • DON.T GRASP THE EXPOSED CUTTING BLADES or cutting edges when picking up or holding • DO NOT OPERATE gardening appliances in gaseous or atmospheres. Motors in these appliances sparks might ignite fumes. IMPORTANT WARNINGS FOR SHRUBBERS & SHEARS 1. Keep hands away from blades. 2. Do not charge the appliance in rain, or in wet locations. 3. Do not use battery operated appliance in rain. SAVE THESE INSTRUCTIONS Extension Cord Make sure your extension cord is in good condition. When using anextension cord be sure it is heavy enough to carry the current yourproduct will draw. An undersized extension cord will cause a drop inline voltage resulting in loss of power and overheating. The followingtable shows the correct size to use depending on cord length andnameplate ampere rating. If in doubt, use the next heavier gage. Thesmaller the gage number, the heavier the cord. Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 (0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m) 240V 0-50 51-100 101-200 201-300 (0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m) Ampere Rating More Not more American Wire Gage Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended 3 90556224 12/4/12:42 Page 4 Features 1. On/off switch 2. Lock-off button 3. Blade release button 4. Grass Shear blade (GSL35, GSL75, GSN30, GSN35) 5. Shrub Trim blade (GSL35, GSL75, GSN32, GSN35) 6. Blade cover (not shown) Assembly WARNING: Avoid accidentally switching the tool on 52143during assembly. Fitting and removing the blade (fig. A, B, C) The shear blade (4) has been designed for trimming grass and weeds. The trim blade (5) has been designed for trimming hedges and shrubs. • To remove the blade cover (6). Push and hold the blade release button (3) in the direction of the arrow (fig. A) • Slide the blade cover (6) backwards and lift it off (fig. A-1). Make sure that the blade is located under edge marked .X. (fig. B-1) and then lower the blade onto the pins. A B • While holding the blade pins (Fig. C), locate the (6) and slide it forward (fig. Note: No alignment of blade with drive pin is required and operation the blade cover release button required when re-fitting the blade cover. Charging Procedure The battery needs to be charged before first use and whenever it fails to produce power on jobs that were easily done before. When charging the battery for the first time, or after prolonged storage, it will only accept an 80% charge. After several charge and discharge cycles, the battery capacity. The battery may become warm while charging; this normal and does not indicate a problem. C WARNING: Do not charge the battery at ambient temperatures below 36° F (2°C) or above 104°F (40°C). Recommended charging temperature: Approximately 75°F (24°• Note: The charger plug incorporates lock outs to prevent the use of incorrect chargers. The plug must be correctly oriented when inserted. • Insert the charger plug into the charger connector at the rear of the tool (fig. D) . • Plug the charger into a 120V outlet. • Charge the tool for 16 hours before first use. For catalog numbers GSL35, GSL75: • The charger indicator light will come on indicating that the tool is charging. D • When the charge is complete the light will go out. For catalog numbers GSN30,GSN32, GSN35: • The charger indicator light will come on indicating that the tool is charging. • The light will stay on as long as the charger is connected to the tool and plugged into a working outlet. 4 5 • It WILL NOT flash, or go out when the charging cycle is complete. To maximize the lifetime of the battery, it is recommended to keep the battery connected to the charger whenever the to...
Este manual também é adequado para os modelos :Clippers - GSL35 (1.23 mb)
Clippers - GSL75 (1.23 mb)
Clippers - GSN30 (1.23 mb)
Clippers - GSN35 (1.23 mb)