Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
See figure 11. FIGURE 11 CONTROLS THROTTLE CONTROL The throttle control lever is located on the handle panel. It regulates the engine speed and stops the engine. See figure 12. DEPTH CONTROL ADJUSTMENT The engagement handle controls the clutching and declutching of the belt. To declutch, the handle is pulled back toward the operator. The farther forward the handle is pushed, the deeper the cut. To move the engagement handle, first move it to the left so the handle is out of the notch. See figure 12. NOTE If belt slips when engagement handle is in the engaged position, lengthen the clutch rod by turning the rod adjustment link. Refer to figure 10. FIGURE 12 8 BLADE PLANE ADJUSTMENT The cutting blade can be adjusted to eight positions from vertical to horizontal. To adjust, release the adjustment lever on the pivot bracket and rotate the >indle housing. Place adjustment lever in notch ^esired. See figure 13. When the blade is adjusted toward the horizontal position, the front wheels must also be adjusted. Remove the two hairpin clips and slide the spacer and wheel to the right as shown in figure 14. Reinsert the hairpin clips. NOTE If the wheels are not adjusted, the blade will hit the left front wheel, causing the belt to slip. Hairpin Clips Become familiar with all the controls and adjustments before operating the edger so you can adjust it easily to a variety of cutting and trimming conditions. While the engine is running, DO NOT ATTEMPT TO MAKE ANY ADJUSTMENTS except with the throttle control. OPERATION 1. Fill the crankcase with oil using a high quality detergent oil -classified "For Service MS." Nothing should be added to the recommended oil. SUMMER - Use SAE 30. WINTER -(Below 40°F.) Use SAE 5W-20 or SAE 10W. Place the engine level. Remove filler plug. FILL THE OIL SUMP TO POINT OF OVERFLOW. Pour slowly. See figure 15. 2. Fill the fuel tank with clean, fresh, lead-free, low lead, or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Move the engagement handle (depth control) back as far as it will go and place in the last notch. See figure 12. 4. Set the throttle control in "START” position. 5. Pull the choke knob out. NOTE A warm engine may not require choking. 6. Grasp the starter handle and pul! out the cord rapidly. Return it slowly to the engine. If the engine does not start after two pulls, move the throttle control to the "FAST" position. 7. After engine starts, push choke knob in gradually. To stop engine, move throttle control to "STOP" position. Disconnect spark plug wire and ground to prevent accidental starting while equipment is unattended. 9 I A CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. OPERATING THE EDGER 1. Set the adjustment lever (refer to figure 12 in the second notch at the top to edge vertici lly. See figure 16. FIGURE 16 2. Set the adjustment lever (refer to figure 13) in the first notch at the top for trenching. See figure 17. FIGURE 17 3. To edge along a curb, remove the hairpin clip from the left side of the front axle, slide the left wheel toward the right side of the unit and replace the hairpin clip. See figure 18. Lower the right rear wheel by moving the height adjustment lever toward the engine, pivoting the w leel to the desired depth and releasing the lever. See figure 19. FIGURE 18 Height Adjustment Lever FIGURE 19 4. To operate the unit as a trimmer, move the adjustment lever and rotate the cutting blade 90°. See figure 20. Move the front wheels all the way to the right, as described in the Control section. ▲ CAUTION Do not adjust the blade guard with the engine running. FIGURE 20 LUBRICATION Wheels - The wheels are plastic and require no lubrication. Engine - Refer to engine manual for lubrication instructions. Cutting Head Bearings - The two ball bearings in the cutting head are lubricated and sealed at the factor ' and require no lubrication. Lubricate all other me ing parts with engine oil. Shaft - Lubricate the two bearings and under the compression spring on the shaft with light oil at least once a season. See figure 21. 10 MAINTENANCE AC WARNING \ Disconect the spark plug wire and ground against the engine before performing any adjustment, repairs or maintenance. BLADE REMOVAL Use a wrench on both sides of the blade when removing it for replacement. BELT REMOVAL 1. To remove the V-belt, remove the belt guard v. assembly at the engine pulley. Remove the hex nuts and lock washers. See figure 21. 2. Remove the belt guard at the spindle assembly by removing two hex bolts, lock washers and hex nuts. See figure 22. 3. Remove the old belt, and reassemble with a new belt, part number 754-0142. FIGURE 22 ENGINE OIL Check oil level before starting engine and after every 5 hours of operation....
Este manual também é adequado para os modelos :Clippers - 24604-9 (1.46 mb)