Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• For short hair, a light trimming at the neck and sides may be all that is needed for a well-groomed haircut. • At regular intervals stop cutting, comb the hair and check the results so far. Hair cutting with comb attachment (4-17 mm remaining hair length) - Begin with the setting for maximum hair length (i.e. position 7). After you have familiarized yourself with the product and have gained some experience, you may select a particular hair length. - You can select seven hair length settings (see fig. 2). Setting Hair length (mm) 7 17 6 15 5 13 4 11 3 9 2 7 1 4 - Before cutting, comb the hair so that it falls naturally. - In general, it is advisable to start from the neck and work towards the top of the head. Next cut the front and the top of the head (fig. 18). Hold the clipper so that the flat side of the comb attachment is directed towards the head. Move it slowly upwards and then away from the head, cutting only a small amount at a time. In the same manner cut the hair at the sides and the back of the head (fig. 19, 20). - If you want the hair cut on the sides or back of the head shorter than on top, change to a lower hair length setting and continue to cut against the direction of the hair growth. Cutting over styling comb or fingers If you want to cut the hair to a length of more than 17 mm, you can use the “over styling comb” method. - Remove the comb attachment (fig. 3). - Lift a small section of hair at a time with a styling comb (fig. 21) or grasp the section of hair between two fingers (fig. 22). Move the comb or fingers through the hair until only the length sticks out which you want to clip off. - Trim the hair protruding from the comb or fingers. Continue this procedure working from the front to the back of the head. As you work to the back, you may gradually cut hair shorter. To check the cutting length, take a cut-off hair section for measuring. - Comb frequently to remove cut hair and to check for uneven areas. Outlining - Comb the hair. - Remove the comb attachment (fig. 3). - For even hair length at the base of the neck cut the hair as shown in fig. 23, holding the clipper in reversed position lightly against the hair. Make overlapping strokes downwards to the neck (fig. 24). - Proceed in the same manner for cutting sideburns (fig. 25). - For cutting the hair close to the ears put one corner of the cutter on the hair. Ensure that the teeth are at a safe distance from the ears (fig. 26). Slowly and carefully shape the desired outline of the hair (fig. 27). Crew cut (fig. 28) - Comb the hair into its natural direction. - Select hair length setting 7 (maximum hair length). Cut the hair from the back side of the neck towards the crown (fig. 29). - Cut the sides of the head making overlapping strokes straight upwards (fig. 30), i.e. parallel to the sides of the head. Hold the comb attachment flat against the head. Move the clipper slowly through the hair, leaving the hair on top of the head uncut. - If you wish you can cut the hair at the neck and sides a second time, using a lower position (i.e. 3 or 4). - For a flat top look, cut the hair on the top of the head over a styling comb or over the fingers (fig. 31, 32) using the hair clipper without comb attachment. Also refer to section “Cutting over styling comb or fingers”. - Finish the haircut by outlining the neckline and sideburns. Also refer to section “Outlining”. Short cut - Comb the hair into its natural direction. - Select the desired hair length for the back and the sides of the head. - Cut the back and the sides of the head making overlapping strokes straight upwards (fig. 33). Hold the comb attachment flat against the head. Move the clipper slowly through the hair, leaving the hair on top of the head uncut. - Select the desired hair length for the top of the head. - Cut the top of the head (fig. 34). Start at the front side and work towards the crown. Hold the comb attachment flat against the head. - For outlining use the hair clipper without comb attachment. Also refer to section “Outlining”. Description generale (fig. 1) A Guide de coupe (ajustable, detachable) B Unite de rasage (detachable) C Reglage de longueur de coupe (pressez et faites glisser) D Interrupteur Marche/Arret | = Marche O = Arret E Prise pour connecteur (basse tension) F Connecteur (basse tension) G Fiche avec transformateur incorpore H Brosse I Huile J Peigne Preparation de la tondeuse a cheveux a l’emploi En fonction de l’application desiree, vous pouvez utiliser la tondeuse a cheveux avec ou sans le guide de coupe. Si vous utilisez le guide de coupe vous pouvez selectionner 7 longeurs de coupe. Faites glisser le bouton de controle en appuyant sur le bouton de deverrouillage (sur sommet). Lorsqu’il est libere, le bouton de controle est verrouille dans la position selectionnee. Taille avec guide de coupe - Selectionnez la longueur de coupe desiree (fig. 2). Pressez (1) et faites glisser le bouton de controle (2) sur une des 7 positions. Relachez le bouton. Tail...
Este manual também é adequado para os modelos :Clippers - HS015/63 (831.89 kb)