Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
2. Gently lift off the front panel while guiding attached wires and thermometer probe to prevent damage. (Fig. 9) 3. Leaving wires attached, gently place front panel face down on a clean work space. (Fig. 10) 4. To replace front cover, reinsert thermometer probe into receptacle, guide wires back into place and reattach panel with the five phillips head screws. Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 6-1c. Replacing the power indicator lamp module. Required: Wiring markers (color or number codes), Electrical tape 1. Remove front panel as found in section 6-1b. 2. Mark all the wires connected to the power indicator lamp module with a color code or number to make proper re-connection easy (Fig. 11) 3. Remove the wire nuts and free the power indicator lamp module wires. 4. From the back side of the front panel, depress the plastic tabs on the base of the indicator lamp module and push it out the front of the panel. (Fig. 12) . 5. Feed the wires of the replacement indicator lamp module through the opening and snap the new indicator lamp module into place. 6. Reconnect wiring with each of the two new wires going to a different wire nut (it doesn't matter how you match the new module wires). Re-tape over wire nuts and wires. **WARNING: Be sure to correctly match the other wires that were connected at the two wire nuts. 7. Replace the front panel (section 6-1b). 6-1d. Replacing the thermostat indicator lamp module. Required: Medium (6") flathead screwdriver, Medium (6”) phillips screwdriver, Wiring markers (color or number codes), Electrical tape 1. Remove front panel as found in section 6-1 b. 2. Mark all the wires connected to the thermostat indicator lamp module and thermostat with a color code or number to make proper re-connection easy. (Fig. 11) 3. Locate the thermostat indicator lamp module wire that connects to a wire nut and remove that wire nut, freeing all wires. (Fig. 13) 4. Remove the indicator lamp module wire from the terminal on the back of the thermostat by removing the electrical tape and reversing the screw. 5. From the back side of the front panel, depress the plastic tabs on the base of the indicator lamp module and push it out the front of the panel. (Fig. 12) 6. Feed the wires of the replacement indicator lamp module through the opening and snap the new indicator lamp module into place. 7. Reconnect wiring with one of the two new wires going to the wire nut and the other to the back of the thermostat (it doesn't matter how you match the new module wires). Re-tape over wire nuts and wires. *'WARNING: Be sure to correctly match the other wires that were connected at the wire nut 8. Replace the front panel (section 6-1 b). 6-1e. Replacing the power switch. Required: Wiring markers (color or number codes), Electrical tape, Wiring diagram for CA43 and CA70 (see step 7 below) 1. Remove front panel as found in section 6-1b. 2. Trace the four wires from the power switch to the wire nuts. Code all wires connected by the four wire nuts to insure proper re-connection. (Fig. 14) 3. Remove the wire nuts and free the power switch wires. 4. From the back side of the front panel, depress the plastic tabs on the base of the power switch and push it out the front of the panel. (Fig. 15) 5. Feed the wires of the replacement switch through the opening and snap the new power switch into place. 6. Reconnect wires using the four wire nuts and the wiring diagram. Re-tape over wire nuts and wires. (Diagram 1) **WARNING: Severe damage can be caused to your unit by improperly connecting wiring. 7. Replace the front panel (section 6-1b). Figure 14 Figure 15 (0. (1. Powe. Indicato. Lam. Powe. Switc. (0. (1. (2. (3. (0. (5. Thermosta. Powe. Cor. (Grd. (2. (3. (4. (1. Heatin. Elemen. (4. (5. Klixo. Thermosta. Fa. Blowe. (0. (1. (5. (1. Thermosta. Indicato. Lam. (0. (1. Coolin. Fa. Diagram 1 1. 6.1f. Replacing the thermometer. Figure 16 Figure 17 Figure 18 Figure 19 Required: Crescent or standard 3/4" wrench 1. Remove front panel as found in section 6-1b. 2. Use a crescent or standard 3/4" wrench to loosen the thermomete...
Este manual também é adequado para os modelos :Móveis - CA43-CV7 or CV13 (1.57 mb)
Móveis - CA43-CV9 (1.57 mb)
Móveis - CA70-CV16 or CV32 (1.57 mb)
Móveis - Convection Heated Holding Cabinet CA34-CV9 (1.57 mb)