Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
There are two types of LEDs you can connect from the system case to the pin: 2-pin single color power LED: The power LED is not able to change its color. Therefore, you can only choose Blinking in the BIOS utility for the power LED to indicate the suspend/sleep mode. LED Status Description Steady Green The system is in the full-on mode. Blinking The system enters the suspend/sleep mode. 2-pin dual color power LED: The 2-pin power LED can change its color to indicate different system states. Therefore, you can select either Blinking or Dual (color) for the power LED to show the suspend/sleep mode. • When you select Blinking: LED Status Description Steady Green The system is in the full-on mode. Blinking The system enters the suspend/sleep mode. • When you select Dual (color) : LED Status Description Steady Green The system is in the full-on mode. Steady Orange The system enters the suspend/sleep mode. 2-17 Chapter 2 HDD LED HDD LED shows the activity of a hard disk drive connected to the IDE1 or IDE2 connector. Avoid turning the power off while the HDD is working. You can connect the HDD LED from the system case to this pin. Speaker (F_P1 only) Speaker from the system case is connected to this pin. If on-board Buzzer is available, then: Short pin 14-15: On-board Buzzer Enabled. Open pin 14-15: On-board Buzzer Disabled. Keylock (F_P1 only) Keylock allows you to disable the keyboard for security purpose. You can connect the keylock to this connector. 2-18 Hardware Setup Power Saving Switch Connector: JGS1 Attach a power saving switch to this connector. Pressing the switch once will have the system enter the sleep/suspend state. Press any key to wake up the system. Wake On LAN Connector: JWOL1 This connector allows you to connect to a LAN card with Wake On LAN function. You can wake up the computer via remote control through a local area network. 2-19 Chapter 2 Wake On Ring Connector: JMDM1 (Optional) This connector allows you to connect to a modem card with Wake On Ring function. The connector will power up the system when a signal is received through the modem card. Note: Modem wake-up signal is active “low’ 2-20 Hardware Setup IrDA Infrared Module Connectors: IR1 & IR2 These connectors allow you to connect to IrDA Infrared modules. You must configure the setting through the BIOS setup to use the IR function. The difference between IR1 & IR2 is that IR2 is compliant to Intel Front Panel I/O Connectivity Design Guide. IR1 IR2 Pin Definition Pin Signal 1 Not assigned 2 NC 3 VCC 4 GND 5 IRTX 6 IRRX IR1 Pin Definition Pin Signal 1 VCC 2 NC 3 IRRX 4 GND 5 IRTX 2-21 Chapter 2 Fan Power Connectors: C_FAN1/S_FAN1 The C_FAN1 (processor fan) and S_FAN1 (system fan) support system cooling fan with +12V. It supports three-pin head connector. When connecting the wire to the connectors, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control. SENSOR +12V GND C_FAN1 1. Always consult the vendor for proper CPU cooling fan. 2. CPU Fan supports the fan control. You can install the PC Alert utility that will automatically control the CPU Fan speed according to the actual CPU temperature. 2-22 Hardware Setup CD-In/Aux Line-In/Modem-In Connector: CD_IN1/AUX_IN1/ MDM_IN1 CD_IN1 connector is for CD-ROM audio connector. AUX_IN 1 connector is for DVD add-on card with Line-in connector. MDM IN 1 connector is for modem with internal audio connector. Note: MonoOut is connected to the Modem speaker-out connector. Phone_In is connected to the Modem Microphone-In connector. 2-23 Chapter 2 USB Front Panel Connectors: USB1 & USB2 The mainboard provides two Front U SB (Universal Serial Bus) pin headers that allow you to connect optional USB ports for front panel. Different from USB1, USB2 is compliant to Intel Front Panel I/O Connectivity Design Guide. 2 ' iu £E0D0 1 9 USB2 2 IU ££@30 1 9 USB1 USB2 Pin Definition USB1 Pin Definition *USB_FP_OC0 is Front Panel USB Overcurrent signal (Ports 2 & 3) Pin Description Pin Description Pin Description Pin Description 1 VCC 2 VCC 1 VCC 2 GND 3 USB3- 4 USB2- 3 USB2- 4 GND 5 USB3+ 6 USB2+ 5 USB2+ 6 USB3+ 7 GND 8 GND 7 GND 8 USB3- 9 NC 10 *USB_FP_OC0 9 GND 10 VCC Note: You can use only ONE USB header to connect USB ports. Make sure you choose the appropriate one for your USB ports. 2-24 Hardware Setup Front Panel Audio Connector: JAUDIO1 You can connect an optional audio connector to the Front Panel Audio Header. Pin number 1to 10 of the audio pin header is compliant to Intel Front Panel I/O Connectivity Design Guide. JAUDIO1 Pin Definition (1~10) Pin Signal Description 1 AUD_MIC Front Panel Microphone input signal 2 AUD_GND Ground used by Analog Audio...