Assessments - 1, GPA: 3 ( )

Fabricante : Campbell Hausfeld Arquivo Tamanho: 6.65 mb Arquivo Nome : Língua de Ensino:

m. Do not operate the pressure washer with the inlet water screen removed. Keep screen clear of debris and sediment. n. NEVER operate pressure washer with broken or missing parts. Check equipment regularly and repair or replace worn or damaged parts immediately. o. Use only the nozzles supplied with this machine. p. NEVER leave the wand unattended while the machine is running. q. ALWAYS hold gun and wand firmly when starting and operating the machine. r. NEVER allow the unit to run with the trigger released (off) for more than one minute. Resulting heat buildup will damage the pump. s. Release the trigger when changing from high to low pressure modes. Failure to do so could result in damage to the nozzle. Operating Instructions and Parts Manual t. NEVER store the pressure washer outdoors or where it could freeze. Freezing temperatures can seriously damage the pump. serVICe a. When servicing a tool, use only identical replacement parts. Use only authorized parts. sAVe these InstruCtIons — do not dIsCArd NOTE: The DANGER, WARNING, CAUTION, and NOTICE notifications and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Frequently Asked Questions Why don’t I have any water pressure? • Is the water hose attached to the pressure washer? • Is the water turned on? • Check for any kinks, leaks, or blockage in the hoses, fittings, or the nozzle. • Is the quick connect tip in place? (See Page 10). • Is the inlet filter screen free of debris? Check and remove debris if needed. how do I get high pressure? • Use any color tip except black. The black tip is only used for low pressure detergent application. how do I get the soap suction to work? 1. Connect the clear plastic chemical suction tube to the plastic hose barb on pump, insert the other end into your detergent. 2. Install the black spray tip to apply low pressure detergent. Why doesn’t the pressure washer apply detergents with high pressure? Detergents “bounce” off cleaning surfaces as fast as they are applied. The pressure washer’s features allow for a detergent to be drawn while in low pressure mode only. By applying detergent at low pressure, the effect of “bouncing” is reduced. Also, detergents are only effective when time is allowed for them to work on the surface of whatever is being cleaned. After applying the detergent, wait 1-3 minutes while it works, and then proceed to rinse the surface with high pressure. What maintenance do I need to perform on my pressure washer? 1. After turning off the pressure washer and the water, depressurize the hose by triggering the gun. 2. Remove the garden hose and high pressure hose from the pump. 3. Turn the motor on for 5 seconds to purge water from the pump. This will help protect the pump from damage. 4. Do not store your pressure washer in an area where the temperature will drop below 32. F. 5. Follow proper storage and winterizing instructions found on pages 13 and 14. What do I do if I’m missing a part? Call Campbell Hausfeld at 1-800-330-0712 and we will promptly replace your missing parts. Do not return the pressure washer to the retailer! Where can I buy accessories for my pressure washer? • If you can’t find accessories at the store where you purchased your pressure washer, call Campbell Hausfeld 1-800-330-0712 or visit our website at Who do I call if I have questions or problems? Call Campbell Hausfeld 1-800-330-0712 (U.S.A.) Models CP5211, CP5216 and CP5321 Unpacking Quick Connect Lance Operating Instructions and Spray Parts Manual Gun Carriage Bolt Spray Tips Pressure Washer (Pump, Motor, and Cart Base) Star Knob Cart Handle Assembly High Pressure Hose Contents In the CArton u One pressure washer (pump, motor, and cart base) u One cart handle assembly u One spray gun and quick connect lance u Two spray tips for Model CP5216 Five spray tips for Models CP5211 and CP5321 u One high pressure hose u One pack of nuts, bolts, and manuals AddItIonAl IteMs not InCluded u ANSI Z87 Eye Protection u Garden Hose After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose, missing or damaged parts. Make sure to tighten fittings, bolts, etc., before using the pressure washer. Check to be sure all supplied accessories are enclosed with the unit. If any parts are missing, DO NOT RETURN THE UNIT TO THE RETAILER. Know the unit’s model number (located on the serial number tag on the pressure washer frame) and call 1-800-330-0712 for replacement parts. Do not operate the unit if it’s damaged during shipping, handling, or use. Damage could result in bursting and cause injury or property damage. read & Follow All Instructions save these Instructions do not discard Figure 2 www www.chpower.chpower.com .com.com Operating...

Baixe o seu

Para fazer o download, introduza 2 dígitos :