Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Slide the handle assembly over the lower legs of the cart base. Use the (supplied) star knob and bolts to secure the handle to the legs (See Figure 9). 2. Slide clear plastic detergent hose onto brass hose barb (See Figure 10). 3. Insert quick connect spray tips into rubber holders on front of the placard. (See Figure 11). 4. Secure garden hose (not included) to the inlet connection on pump (See Figure 12). 5. Connect the high pressure hose to the pump outlet (See Figure 13). 6. Attach the lance to the gun (See Figure 14). 7. Install quick connect tip (See Figure 15). Figure 9 - Assemble handle Figure 10 - Attach suction tube to barb fitting Figure 11 - Insert spray tips into the holder Figure 13 - Connect high pressure hose to pump Figure 14 - Attach lance to gun Figure 15 - Quick connect tip Garden Hose Pump Inlet Thermal Relief Valve Pump Outlet Detergent Hose / Chemical Tube Hose Barb Figure 12 - Pump hook up Models CP5211, CP5216 and CP5321 Assembly and Preoperation (Continued) trIgger sAFety lAtCh In the engaged position, the trigger safety latch prevents the gun from being triggered accidentally. Push the latch fully up to engage it (See Figure 16 and 17). Always engage the trigger safety latch Figure 16 - trigger locked Figure 17 - trigger unlocked when the unit is not in use. Operation surFACe PrePArAtIon The following cleaning procedure will help you organize your cleaning task and ensures that you will achieve the best results in the shortest amount of time. Remember to use the spraying / cleaning techniques mentioned in the following section. Before starting a pressure washer cleaning job, prepare the surface you intend to clean. Clear furniture from the area and make sure that all windows and doors are closed tightly. Also, protect all plants and trees near the cleaning area with a drop cloth. A covering ensures that your plants won’t be sprayed by the detergents. stArt uP ALWAYS use this start up procedure to ensure that the unit is started safely and properly. If water has frozen in the pressure washer, thaw the pressure washer in a warm room before starting. DO NOT pour hot water on or into the pump; internal parts will be damaged. 1. Ensure that the power switch is in the “OFF” position. 2. Attach a garden hose to the inlet side of the pump and connect it to the water supply. Use a hose with an internal diameter (I.D.) of 5/8 in. (1.58 cm) and a length of 50 ft. (15 m) or less. Some local plumbing codes require backflow prevention when connecting to a fresh water supply. Install a backflow preventer upstream from the pump if necessary. a. If inlet water pressure is over 100 psi, install a regulating water valve at the garden hose connection. b. Do not exceed 100. F (38. C) inlet water temperature. NOTE: The inlet water supply must have a minimum flow rate of 5 gpm (19 lpm). 3. Turn the water supply ON. Never run the unit dry. Be sure the water supply is completely turned on before operating the unit. 4. Trigger the gun until water sprays from the tip indicating that all air is purged from the system. Set the trigger safety latch. 5. Plug the power cord into a grounded 120V outlet, that is on a dedicated circuit. Press the reset button on the GFCI plug adapter. This must be done each time the unit is plugged into an outlet. Operating Instructions and Parts Manual Operation (Continued) InItIAl hIgh Pressure rInse Spray the cleaning surface with water to clear off any dirt or grime that may have collected on the surface. Doing so allows the detergent to attack the deep down dirt that has worked its way into the cleaning surface. Trigger the gun 3 to 5 times to get any trapped air out of the system. Adjusting the spray Fan Angle Two quick connect tips for Model CP5216 or five quick connect tips for Models CP5211 and CP5321 are included with this pressure washer. The tips have a range of spray fan angles, ranging from 0°, narrow high impact, to a 65° wide fan spray. Pressure can also be adjusted by moving closer or further away from the cleaning surface and by adjusting the spray fan angle as shown. Angle to the Cleaning surface When spraying water against a surface, you can generate maximum impact by striking the surface head on. However, this type of impact can cause dirt particles to embed in the surface and can prevent the desired cleaning action. The optimum angle for spraying water against a cleaning surface is 45 degrees. Spray water against a surface at a 45 degree angle to achieve the most beneficial impact force and to efficiently remove debris. distance From Cleaning surface The distance between the spray tip and the cleaning surface is another factor that affects the impact force of the water. The impact force of the water increases as the tip is moved closer to the surface. how to Avoid damaging surfaces Damage to cleaning surfaces occurs because the impact force of the water exceeds the durability of the surface. You can vary the impact force by cont...
Este manual também é adequado para os modelos :Equipamento de lavagem - IN469800AV (6.65 mb)
Equipamento de lavagem - CP5216 (6.65 mb)
Equipamento de lavagem - CP5321 (6.65 mb)