Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Hexagon key Specifi cations: See model tag (14) of machine. We reserve the right to alter the specifi cations. 5 6 Nilfisk C 105.5 / C 115.3 EN 3 Before you start using your pressure washer 3.2 Mounting of quick coupling 1. Screw the quick coupling tight on to the water inlet (2). Note: The inlet fi lter (2a) must always be fi tted in the water inlet pipe to fi lter out sand, lime stone and other impurities as these will damage the pump valves. Caution: Failure to fi t the fi lter will invalidate the guarantee. 3.1 Mounting of trolley handle (C 115.3) 3.3 Mounting of high pressure hose on spray handle 1. Attach the high pressure hose (4) to the spray handle (7). Detach the high pressure hose by pressing the pawl (A). 1. Place the trolley handle on the machine. 2. Secure the handle by mounting the 2 screws. Use the enclosed hexagon key. . A 7 Nilfisk C 105.5 / C 115.3 4 Operating your pressure washer EN 4.1 Connection of high pressure hose 1. Mount the high pressure hose on the outlet (3). 4.2 Mounting of spray lance and Click & Clean nozzles 1. Push the spray lance (6) into the spray handle (7) and screw it on. Note: The spray lance (6) has a built-in low pressure nozzle that can be used for fl ushing away dirt. 2. Attach the nozzle. Warning: When attaching the Click & Clean nozzles, the pawl on the side of the spray lance (6) should come out again. Note: The foam sprayer (11) features a swivel lock, which must be positioned in the hole in the Click & Clean spray lance (6). Press the pawl to detach the Click & Clean nozzle. . EN EN Nilfisk C 105.5 / C 115.3 4.3 Water connection 4.4 Start and stop of the machine An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. NOTE: Connection to the public mains according to regulations. The spray lance is affected by a thrust during operation - therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground. 1. Check that the machine is in uprigth position. NOTE: Do not place the machine in high grass! 2. Release the trigger lock (7a). 3. Activate the trigger of the spray handle and let the water run until all air has escaped from the water hose. 4. Press the Start/stop switch "I" (1). 5. Activate the trigger of the spray handle. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. IMPORTANT! Only use water without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own well), an additional filter (106411231) should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the fi lter is fitted in the water inlet pipe and that it is not clogged up. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 40°C). 3. Turn on the water. Do not cover the machine during operation or use it in a room without adequate ventilation ! Note: If the ma chine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Press the start/stop switch "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray handle (7a). When releasing the trigger of the spray handle, the machine automatically stops. The machine will start again when you re- activate the spray handle. 8 9 Nilfisk C 105.5 / C 115.3 EN 5.2 Winding up of electric cable and high pressure hose (C115.3) 5 After using your pressure washer To avoid accidents, the electric cable and the high pressure hose should always be winded carefully up around the handle. Wind up the cable on the appropriate hook. 5.1 Storing the washer The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (press the start/stop switch “O” (1) and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray handle. 3. Stop the machine, unplug and wind up hose and cable. 4. Place spray handle, nozzles and other accessories in the holders of the machine. Should the machine by mistake be frozen, it will be necessary to check it for damage. NEVER START-UP A FROZEN MACHINE. Frost damages are not covered by the guarantee! . 5.3 Storage of accessories The standard accessories - spray handle, lance, nozzles and foam sprayer can be stored on the pressure washer. Nilfisk C 105.5 / C 115.3 EN 6 Maintenance 6.1 Cleaning of water inlet fi lter 6.2 Cleaning of nozzle WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice: • Wash out water hose, high pressure hose, spray lance and accessories before mounting. • Clean t...
Este manual também é adequado para os modelos :Equipamento de lavagem - C 105.5 (1.1 mb)