Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Note: This monitor supports multiple VGA modes. Refer to the Preset Display Modes Table for a listing of modes supported by this monitor. Note PROBLEM: Picture is unclear and unstable. The picture is unclear and unstable, please perform the following steps : 1. Enter PC to "Shut Down Windows" status while you're in MS-Windows environment. 2. Check the screen to see if there's any black vertical stripes appear. If there are, take advantage of the "Clock" function in OSD menu and adjust (by increment or decrement numbers) until those bars disappear. 3. Move to "Phase" function in OSD menu again and adjust the monitor screen to its most clear display. 4. Click "No" on "Shut Down Windows" and back to the normal PC operating environment. PROBLEM: There is no picture on the monitor. If there's no picture on the monitor, please perform the following steps: 1. Make sure the power indicator on the monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for information on timing. 2. Turn off the monitor and then turn it back on again. If there is still no picture, press the Adjustment Control button several times. 3. If step 2 doesn't work, connect your PC system to another external CRT. If your PC system Functions properly with a CRT monitor but it does not function with the monitor, the output timing of the VGA card may be out of the LCD's synchronous range. Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card, and then repeat steps 1 and 2. PROBLEM: There is no picture on monitor. If you have chosen an output timing that is outside of the monitor's synchronous range (Horizontal: 30~ 80KHz and Vertical: 56 ~ 75 Hz), the OSD will display an "Out of Range" message. Choose a mode that is supported by your monitor. Also, if the signal cable is not connected to monitor at all or properly, the monitor screen will display a message "No Input Signal". A Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ¦ Reorient or relocate the receiving antenna. ¦ Increase the separation between the equipment and the receiver. ¦ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ¦ Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Compaq Computer Corporation may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, contact: Compaq Computer Corporation P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call - 1-800- 652-6672 (1-800-OK COMPAQ) For questions regarding this FCC declaration, contact: Compaq Computer Corporation P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call - (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product. Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives impl...