Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
b) System Interconnection Box (AVX-6869): In line with all the system cabling and in an area were it can be easily accessed. c) System Main Cable: Under either seat where monitors are located. Tools and Materials Required: Utility knife or box cutter with sharp blade. Permanent Marker. Tie Wraps. INSTALLATION Optional Bracket Mounting: This procedure describes mounting the system monitor using an optional Surface Mount Bracket (sold separately, # FB1) 1) Start by firmly attaching the Surface Mount Bracket onto a flat surface IMPORTANT NOTICE It is unlawful in most jurisdictions to drive a motor vehicle which is equipped with a television viewer or screen that is located at the point forward of the back of the driver’s seat, or that is visible directly or indirectly, to the driver while operating the vehicle. 5 2) Slide monitor onto Surface Mount Bracket and then tighten the fasten wheel. Monitor Fastener Wheel Surface Mount Fastener Mounting Bracket 3) Adjust viewing angle of monitor by tightening the fastener at the side. Surface Mount 4) When the system components are mounted, test the system to verify that it is functioning correctly. Make sure that no wiring was pinched, or connected improperly during the final installation. 6 Headrest Mounting: 1) Remove the headrest from the vehicle for easiest installation. 2) Lay headrest on a flat surface. 3) Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down. 4) Using a Permanent Marker, mark headrest material along the interior of the Trim Ring. 5) Remove the Trim Ring and mark an “X” from corner to corner as shown. Mounting Trim Monitor Tray Ring Headrest 7 6) Using the utility knife, cut the headrest material along the “X” lines. Do not cut the material along the other lines at this time. 7) This will leave you with an “X” cut as shown. 8) Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. 9) Using your fingers, tear the foam out of the headrest leaving a recess where the shell will be inserted. NOTE: At this point you will need to install the harness up through the area into the recess. It may be helpful to follow one of the posts and tie wrap it to the post for restraint. 8 10) Lay the flaps of headrest material down into the recess and insert the Mounting Tray into the recess. Check for fit. If it does not fit properly, you may need to remove some more foam. NOTE: The Mounting Tray will need to be secured to the headrest, either by using tie straps, screws, ect.. 11) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor. Make sure the connector locks into place. Insert the Monitor into the Mounting Tray and secure the cable using tie wraps or screws 12) Turn the Monitor around and insert it into the Mounting Tray housing. Snap into place. 13) Connect the Monitor power input plug to a DC power source (Red plug +12 VDC, Yellow plug +12 VDC Constant and Black plug (-) to ground). 14) Connect the external video source output signal (from VCP/ DVD, TV Etc.) to the VIDEO IN jack. Test the system to verify proper installation. 9 ELECTRICAL CONNECTION (Wiring Diagram) Video Source Input (1&2) Not Used AV Output 10 Monitor Removal: The following procedure is to remove the Monitor from the Mounting Tray using the supplied Removal Tool. NOTE: Use care when performing this procedure not to scratch any exposed surfaces with the edges of the Removal Tool. Masking tape applied to the two tips or legs of the Removal Tool will help prevent scratching. 1) Locate the Removal Tool and apply tape to the tips. 2) Insert the Removal Tool into the center of the space between the top outer Mounting Tray and the Monitor. You will hear click(s) when inserted correctly. This will disengage the two pressure latches holding the monitor in place. 3) While applying upwardly pressure, pull the Removal Tool out and up. 4) The Monitor will pop out from the top and can be removed by detaching the Monitor Cable. 11 Removal Tool Removal Tool Removal Tool Monitor Cable CONTROLS AND INDICATORS Headphone OPERATION 1. Press power On/Off button to the On position. The LED power indicator will light red. 2. Press the Picture Select button to adjust the picture display characteristics. The adjustments will be shown on the On Screen Display in the following sequence: Contrast, Brightness, Color, and TINT. 3. While in the video adjustment mode, press the up button to increase the selected adjustment level or press the down button to decrease the level. 12 MAINTENANCE To avoid electrical shock, do not open the enclosure. High voltage is present. No user serviceable parts inside the enclosure. Do not use any chemical solvent, cleaning agent or corrosive detergent to clean away dirt on th...
Este manual também é adequado para os modelos :Monitores - LCM5043NP (171.54 kb)
Monitores - LCM5043NP (171.54 kb)
Monitores - LCM5643NP (171.54 kb)