Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are capable of producing an electric shock . The exclamation point within a triangle is intended to alert the user that important operating and servicing instructions are being provided. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: 1. This product is designed to operate with a 12 volt, negative ground battery system. 2. Disconnect the ground wire from the battery terminal before connecting the electrical system. Refer to the electrical connection diagram to avoid wrong connection of the electrical system. Always use authorized service center for service assistance. 3. Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C). 4. Keep the monitor clean and dry. 5. Never attempt your own repairs. This unit should be installed and repaired by qualified technicians or service personnel.. 6. Do not drop the monitor or expose to strong impacts. 7. Do not expose to direct sunlight for extended periods of time. 8. Use proper insulation material to prevent short-circuiting of the supply system. 9. Tighten all loose wires after installation. 1 SYSTEM OVERVIEW The LCM5043NP is comprised of a 5" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor. The LCM5643NP is comprised of a 5.6" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor. The Monitor for both of these systems have a 4:3 Aspect Ratio display that allows the user to select between two video sources (Not Supplied). The Monitors displays all functions with the comprehensive On Screen Display (OSD). Can be used with an optional Wired Headphone. OPTIONAL AUDIO CONNECTION 1) Wired Headphones......................................... P/N =HP275 Wired Headphones 2 MATERIALS LIST 1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.) 2. Remote Control Unit (136B2156) with Lithium Battery, 3V,CR 2025 (1pc.) 3. Interconnect Box (136B2183) (1pc.) 4. Monitor Cable, 8' (112B3152) (1pc.) 5. Headrest Mounting Tray (LCM5043NP=102C3740) or (LCM5643NP=102C3742) (1pc.) 6. Trim Ring for Mounting Tray (LCM5043NP=102B3741) or (LCM5643NP=102B3743) (1pc.) 7. Power Cable, 2.46' (112B3127) (1pc.) 8. Removal Tool (108B3632) (1pc.) 4 VEHICLE PREPARATION 1) Decide on the system configuration and the options that will be installed (i.e. what components, VCP, DVD, TV Tuner, Video Game, Monitor, FM Modulator, etc.). 2) Read the manuals and get familiar with the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products. 4) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle's wiring as well as all areas where interconnecting wire harnesses will be located. If any access holes need to be cut into the vehicle, headrests, or other trim components, this should be performed now. (Refer to the Installation Procedure). 5) Run the wiring harnesses and cabling throughout the vehicle as necessary. (Refer to the wiring instructions for the individual components and accessory options being installed). Be sure, that all the wiring is protected from sharp edges and is routed in such a manner that it will not be pinched, when it is fully installed. Be sure to leave enough slack in the wiring at each component to allow sufficient working room. 6) Remove all the A/V system components from their packaging and then place them in the vehicle at their respective locations. 7) Locate an accessory power source (Red Wire)(+12VDCpresent when the ignition key is in the accessory and run positions. 0VDC should be present, when the ignition key is in the OFF position). Generally, these wires can be found at the ignition switch or fuse box. 8) Locate a Constant Power Source (Yellow Wire)(+12VDC present at all times). NOTE: Ensure that the accessory power is fused at the source. Failure to do so may result in vehicle wiring damage.) Ground the black wire to a chassis ground close to the mounting location of AV sources. 9) Connect all the components together (electrically) and verify that the proper operation of all the system functions. NOTE: This is best done BEFORE the components are permanently mounted. 4 10) After verifying the proper operation of the system, proceed to mount each component. 11) The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focus for the installation of the 12) The best location for the system components is: a) Monitor: Headrest or bracket (optional) mounted onto a flat surface. b) System ...
Este manual também é adequado para os modelos :Monitores - LCM5643NP (171.54 kb)
Monitores - LCM5043NP (171.54 kb)
Monitores - LCM5643NP (171.54 kb)