Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
LCD Display is on. (Refer to the Connecting the LCD Display ) "Check Signal Cable" message. • Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting the LCD Display ) • Ensure that the PC or video sources are turned on. "Not Optimum Mode " message. • Check the maximum resolution and the frequency of the video Adaptor. • Compare these values with the data in the Preset Timing Modes Chart. The picture rolls vertically. • Check if the signal cable is securely connected. Re-connect it, if necessary. (Refer to Connecting a Computer) The image is not clear; picture is • Run Frequency Coarse and Fine tuning. blurred. • Turn on again after removing all accessories (video extension cable, etc.) • Set the resolution and frequency to the recommended ranges. The picture image is unstable and • Check if the resolution and frequency set for the computer video shakes. card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the Ghost images are shown in the LCD Display menu and Preset Timing Modes. picture. The image is too light or too dark. • Adjusts the brightness and contrast. (Refer to the Brightness, Contrast) The screen color is inconsistent. The color image is distorted by • Adjust color using Custom under OSD Color Adjustment menu. dark shadows. The color white is poor. The power Indicator blinks green. • The LCD Display is currently saving the changes made to the settings to the OSD memory. The screen is blank and the power • The LCD Display is using its power management system. indicator light is steady green or • Press a key on the keyboard. blinks every 0.5 or 1 seconds. The screen is blank and it is • If you see the "TEST GOOD" message on the screen when you blinking. pressing the MENU button, check the cable connection between the LCD Display and the computer to ensure that the connector is properly connected. Problems related to Audio Note • Problems related to audio signals and their solutions are listed below. Problems Solutions No sound. • Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display and the audio-out port on your sound card. (Refer to the Connecting the LCD Display ) • Check the volume level. The sound level is too low. • Check the volume level. • If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. The sound is too high or too low. • Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note • Problems related to the remote control and their solutions are listed. Problems Solutions The remote control buttons do not • Check the polarities (+/-) of the batteries. respond. • Check if the batteries are empty. • Check if the power is on. • Check if the power cord is securely connected. • Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicNet Note • Making a Bootable USB Flash Disk. Problems Solutions Making a Bootable USB Flash Disk 1. You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool. (For example, the HP USB Disk Storage Format Tool) 2. Copies the OS ghost image and executables to your USB disk. 3. Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu. 4. Switch your set on while your USB disk is connected and boot up in DOS mode. 5. Run C:\ghost.exe and choose Local > Partition > From Image from the menu. Choose the ghost image to update your USB disk with and choose the target disk. 6. When the ghost image update finishes, the set will be rebooted automatically. Q &A Question Answer How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I Adjusts the resolution? • Windows XP: Set the resolution in the Control Panel > Appearance and Themes > Display > Settings. • Windows ME/2000: Set the resolution in the Control Panel > Display > Settings. * Contact the video card manufacturer for details. How can I set the Power Saving • Windows XP: function? Set the resolution in the Control Panel > Appearance and Themes > Display > Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). • Windows ME/2000: Set the resolution at the Control Panel > Display > Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). How can I clean the outer Disconnect the power cord and then clean the LCD Display with a soft case/LCD Panel? cloth, using either a cleaning solution or plain water. Do not leave any detergent or...