Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
1 3 5,6 2 5 4,5 6 1 Press 1/u to turn on the power. 2 Press TUNER/BAND repeatedly until the band you want appears in the display. Each time you press the button, the band changes as follows: FM n AM Getting Started n 3 Press TUNING MODE repeatedly until “AUTO” appears. 4 Press +/–. The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo programme) appear. When you want to stop scanning, press TUNING MODE. continued Step 3: Presetting radio stations (continued) 5 Press MENU/NO then +/– repeatedly until “Frq-Memory?” appears then press ENTER/YES. The preset number flashes. Proceed to step 6 while the preset number is flashing. If the unit is not operated for more than 16 seconds, the preset number disappears and the unit returns to the status of step 3. If this happens, start over from step 4. 6 Press ? or / on the remote to select the preset number you want then press ENTER/YES. The station is stored. Select 1 to 20 for FM, and select 1 to 10 for AM. 7 Repeat steps 2 through 6 to preset other stations. To tune in the station manually 1 Press TUNING MODE repeatedly until “MANUAL” appears in step 3. 2 Press +/– repeatedly to tune in the station and continue from step 5. To change the preset number Start again from step 1. To change the AM tuning interval (except for European model) The AM tuning interval is factory-set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the TUNING + button, turn the power back on. When you change the interval, all the AM preset stations are erased. To reset the interval, repeat the same procedure. Tips • When a new station is memorized, the station formerly memorized at that preset number is erased. • The preset staions are retained for a week even if you disconnect the mains lead or if a power failure occurs. Saving the power in standby mode You can lower the power consumption to a minimum (Power Saving Mode) and save energy in the standby mode. DISPLAY / Press DISPLAY on the remote or on the CMT-SD1 when the power is off. The unit switches to the Power Saving Mode and the clock display disappears. The system turns on/off by pressing 1/u. Tips • u indicator and timer indicator (when the timer is set) light up even in the Power Saving Mode. • The timer work in the Power Saving Mode. To cancel the Power Saving Mode Press DISPLAY. The clock display appears. Basic Operations Playing a CD To turn on the system, press 1/u. 1/u (Power) 1 2 2 . .± VOLUME 0) CD ( P =/+ 0/) VOL +/– 1 Press § to open the disc tray and place a CD. With the label side up. When you play a single CD, place it on the inner circle of the tray. To close the disc tray, press § again. 2 Press ·. (or CD ( on the remote). The disc tray closes and play starts. To Stop play Pause Select a track Find a point in a track Remove CD Adjust the volume Tips Do this Press .. Press ·. (or P on the remote). Press again to resume play. Press . or ± (or =/ + on the remote) repeatedly until you find the desired track. Press and hold 0 or ), during play and release it at the desired point. Press §. Turn VOLUME (or press VOL +/– on the remote). Basic Operations • You can switch from another source to the CD player and start playing a CD by pressing ·. (or CD ( on the remote) (Automatic Source Selection). • If you push the disc tray lightly, the disc tray closes and play starts automatically (Auto Play). Listening to the radio Preset radio stations in the tuner’s memory first (see page 7). To turn on the system, press 1/u. 1/u(Power) VOLUMETUNING +/–TUNER/BAND 2 +/– 1 1 STEREO/ MONO VOL +/– 3 1 Press TUNER/BAND repeatedly until the band you want appears. Each time you press the button, the band changes as follows: FMn AM n TUNED STEREO AUTO MHz 2 Press TUNING MODE repeatedly until “PRESET” appears. TUNED STEREO PRESET MHz 3 Press +/– to select the desired station’s preset number. TUNED STEREO PRESET MHz To Do this Turn off the radio Press 1/u to turn off the system Adjust the volume Turn VOLUME (or press VOL +/– on the remote) To listen to non-preset radio stations • Press TUNING MODE repeatedly until “MANUAL” appears in step 2, then press TUNING + or – repeatedly to tune in the desired station (Manual Tuning). • Press TUNING MODE repeatedly until “AUTO” appears in step 2, then press TUNING + or –. The frequency indication changes and scanning stops when the system tunes in a station (Automatic Tuning). To cancel the Automatic Tuning Press TUNING MODE. Tips • You can switch from another source to the tuner by pressing TUNER/BAND (Automatic Source Selection). • To improve broadcast reception, reorient the supplied aerials or connect an optional external aerial. • When an FM programme has static noise, press STEREO/MONO until “MONO” appears. There will be no stereo effect, but the reception will improve. Press again to restore the stereo effect. The CD player The CD player Playing...
Este manual também é adequado para os modelos :Stereo - CMT-SD1 (272.53 kb)