Assessments - 5, GPA: 3.8
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
The type of timer (DAILY 1 or DAILY 2), followed by the start time, stop time and the music source, appears, then the original display appears. 9 Turn off the power. To check the setting Press CLOCK/TIMER SELECT and press .or >repeatedly to select the respective mode (DAILY 1 or DAILY 2), then press ENTER on the remote. To change the setting, start over from step 1. To cancel the timer operation Press CLOCK/TIMER SELECT and press .or >repeatedly to select “TIMER OFF”, then press ENTER. Notes • You cannot activate DAILY 1 and DAILY 2 timer at the same time. • You cannot set timer if the timer on and off times are the same. • When you use the Sleep Timer, Daily Timer and Timer recording will not turn on the system until the Sleep Timer turns it off. • You cannot activate Daily Timer and Timer recording at the same time. Tip The power turns on 15 seconds before the preset time. Timer-recording radio programs To timer-record, you must preset the radio station (see “Step 3: Presetting radio stations” on page 8) and set the clock (see “Step 2: Setting the time” on page 7) beforehand. 2 CLOCK/ jJlLhHSsHSs 7 TIMER SELECT 3,4 3,4 1 Tune in the preset radio station (see “Listening to the radio”). 2 Press CLOCK/TIMER SET. “SET (DAILY 1)” appears. 3 Press .or >repeatedly to select “REC”, then press ENTER. “ON” appears and the hour indication flash in the display. REC 4 Set the time to start recording. Press .or >repeatedly to set the hour, then press ENTER. The minute indication starts flashing. REC Press .or >repeatedly to set the minute, then press ENTER. The hour indication flashes again. 5 Set the time to stop recording following the above procedure. The start time appears, followed by the stop time, the preset radio station to be recorded (e.g., “TUNER FM 5”), then the original display appears. 6 Insert a recordable tape into deck B. 7 Turn off the power. When the recording starts, the volume level is set to the minimum. To check the setting Press CLOCK/TIMER SELECT and press .or >repeatedly to select “REC”, then press ENTER. To change the setting, start over from step 1. To cancel the timer operation Press CLOCK/TIMER SELECT and press .or >repeatedly to select “TIMER OFF”, then press ENTER. Notes • If the power is on at the preset time, the recording will not be made. • You cannot set the timer if the timer on and off times are the same. • You cannot activate the Timer-recording and Daily Timer at the same time. • When you used the Sleep Timer, Daily Timer and Timer recording will not turn on the system until the Sleep Timer turns it off. Optional components Optional components Connecting audio components Select one of the following two connections, depending on the equipment to be connected and method of connecting. Refer to the instructions of each component below. Connecting an MD deck for digital recording You can record from CD into the MD deck digitally by connecting an optical cable. To the DIGITAL IN jack of the MD deck Optical Cover Holder Tip Keep the optical cover at the optical cover holder provided. Connecting an MD deck for listening to music Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press MD (VIDEO). MD (VIDEO) To the audio output of the MD deck Tip When you connect a Sony MD deck, you can use the MD N, X, and xbuttons on this unit’s remote to perform play, pause, and stop operations. Note If you cannot select “MD” even when you have pressed MD (VIDEO), press ?/1while pressing MD (VIDEO) when the power is turned off. “VIDEO” will be switched to “MD”. To return to “VIDEO” do the same procedure. However, you cannot switch from MD to VIDEO or from VIDEO to MD when the system is in the Power Saving Mode (see page 9). Connecting a VCR Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, hold down MD (VIDEO) and press ?/1when the power is turned off. This switches the “MD” function to “VIDEO”. Once you enable the “VIDEO” function, just press MD (VIDEO). By connecting the audio output jacks of your VCR to the MD/VIDEO (AUDIO) jacks using an optional audio cable, you can enjoy video playback in powerful stereo sound. To the audio output of the VCR Note • You cannot switch from MD to VIDEO or from VIDEO to MD when the system is in the Power Saving Mode (see page 9). • If the sound is distorted or too loud when selecting “VIDEO”, or you want to switch back to “MD”, repeat the operation described above for switching to “MD”. Connecting external antennas Connect the external antenna to improve the reception. FM antenna Connect the optional FM external antenna. You can also use the TV antenna instead. Jack type A FM75 AM COAXIAL 75-ohm coaxial cable (not supplied) AM antenna Connect a 6- to 15- meter (20- to 50- feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected. Jack type A Insulated wire (not supplied) FM75 AM COAXIAL Jack type B Insulated wire (...
Este manual também é adequado para os modelos :Stereo - MHC-BX9 (475.06 kb)
Stereo - MHC-DX7 (475.06 kb)