Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
72Cable: RGB-5HD15-X (X = Length in feet 6, 10, 15, 20) V-CB1 Desktop Stand V-CRM-2 2U (1.75” tall) Conversion and Distribution 3 Module Bracket.Up to three Marshall Electronics 4.75” wide conversion or distribution modules can be securely installed into a standard EIA 19 inch rack with the V-CRM-3 mounting bracket. Every V-CRM-3 includes two blank panels for a clean cosmetic appearance. V-CRM-3 Single RU (1.75” tall) Conversion and Distribution 2 Module Bracket.Two Marshall Electronics 7.72” wide or one 7.72” plus one 4.75” wide conversion or distribution modules can be securely installed into a standard EIA 19 inch rack with the V-CRM-2 mounting bracket. Every V-CRM-3 includes one blank panel and one 4.75” adapter for a clean cosmetic appearance. MC-0105 Distribution Amplifier Users Guide 7475Signal Input HD-15 VGA, Composite Video BNC 75., Y/C Video 4 pin Mini- din Signal Output HD-15 VGA (27 Mhz for NTSC) Sample Frequency 27mhz K factor <1% Signal to Noise >42 db Dynamic gain/phase <1% / <1.50 Cable length Up to 350ft (100m) AGC compensated Power required 6V D.C. supplied from external supply (Model V-PS6-1.2A) Dimensions 4.75”W x 3.75”D x 1.0”H Weight 0.55 lbs (0.25kg) V-PS6-1.2A Power Supply Weight 0.20 lbs (0.10kg) 73Electrical Specifications 1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • • Email: sales@lcdracks.com 71 Switch Settings and Indicators77Operational Setup 1. Unpack the MC-0105, and accompanying V-PS6-1.2A power supply and physically inspect for any damage that may have occurred during shipping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606. 2. Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on the sides, closest to the rear of the unit. (See below) Only one screw per side should be removed. Use the same screw to attach the bracket with the flange facing away from the side and parallel to the front of the MC-0105 metal case. The flange has two holes. For desktop use, apply the supplied rubber pads. 3. Connect required cables for signal input and output. All BNC connectors should be rated for 75.. 4. Plug the V-PS6-1.2A power supply into the A.C. source 5. Attach twist lock power connection from V-PS6-1.2A power supply to the back of the unit. 6. Turn on the MC-0105 by depressing the power switch located on the front of the unit. 76Input Connectors S-Video In 4 Pin Din (Fe- male) Pin1 - GND Pin2 - GND Pin3 – Y in Pin4 – C in VGA-In DB HD-15 Female Connector Input Pin-1 Red In Pin-2 Green In Pin-3 Blue In Pin-4 Pin-5 Pin-6 Ground Pin-7 Ground Pin-8 Ground Pin-9 Pin-10 Pin-11 Pin-12 Pin-13 VS In Pin-14 HS In Pin-15 VGA-Out DB HD-15 Female Connector Output Pin-1 Red Out Pin-2 Green Out Pin-3 Blue Out Pin-4 Pin-5 Pin-6 Ground Pin-7 Ground Pin-8 Ground Pin-9 Pin-10 Pin-11 Pin-12 Pin-13 VS Out Pin-14 HS Out Pin-15 6 VDC from V-PS6-1.2A power supply Left Pin - Pos Right Pin- Neg Note: VGA inputs signals of any format will be output as the same format when VGA source is selected. For best operation a multi-sync monitor should be used. Note: NTSC signals are converted to 480x640 VGA resolution output. PAL signals are converted to 576x640 VGA resolution output. 78Input Selection Indicators Power On/Off switch with System indicator. Illuminates Red when Power is connected. Illuminates Green when the MC-0105 is switched on Input Selection Toggle Switch Toggles input source to output selection Analog Video In BNC 1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • • Email: sales@lcdracks.com 77Operational Setup 1. Unpack the MC-0105, and accompanying V-PS6-1.2A power supply and physically inspect for any damage that may have occurred during shipping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606. 2. Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on the sides, closest to the rear of the unit. (See below) Only one screw per side should be removed. Use the same screw to attach the bracket with the flange facing away from the side and parallel to the front of the MC-0105 metal case. The flange has two holes. For desktop use, apply the supplied rubber pads. 3. Connect required cables for signal input and output. All BNC connectors should be rated for 75.. 4. Plug the V-PS6-1.2A power supply into the A.C. source 5. Attach twist lock power connection from V-PS6-1.2A power supply to the back of the unit. 6. Turn on the MC-0105 by depressing the power switch located on the front of the...