Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Turn the knob in a clockwise direction to increase the headphone volume. 28. TRUE BASS LEVEL - This knob is used to control the amount of "TRU BASS" process is applied to the output source signal. 29. HEADPHONE JACK -This jack is used to connect your headphones to the mixer allowing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are rated at 16 ohm, these are highly recommended. Always be sure the Cue Level Volume (27) is set to minimum before you put the headphones on. 30. SPLIT CUE -This button will activate the "Split Cue" function. When used with a set of stereo headphones, the Split Cue function will assign the Cue signal to the left channel of the headphones and the Program (main output) signal to the right channel of the headphones. Essentially splitting the cue signal in half. This process will allow for headphones mixing. Please note that this function will only work with a set of stereo headphones. 31. WOW CONTROL - This button is used to activate the SRS® WOW Process. The WOW™ process is a combination of 3D Stereo Process and the TRU BASS™ Process. WOW is the latest audio technology from SRS Labs and creates extraordinary enhancement to the listening experience. Ordinary stereo presents a limited spatial presentation, and often lack-luster bass (low frequency) performance. Any sound system can deliver an audio performance with drastically improved image size, dynamics and immersion when playing a signal processed with WOW. Because the WOW™ effect combines the 3D Stereo™ Process and the TRU BASS™ Process, the processing of the spatial cues surrounds the listener with a holographic representation of the performance. In addition bass becomes deep, rich and controlled through means that don’t require a speaker with a large woofer or cabinet size. In essence you may eliminate the need of a separate sub-woofer. 32. TRU BASS CONTROL - This button is used to activate the SRS® (Sound Retrieval System®) TRU BASS™ Process. TruBass circuity actively monitors the low-frequency content of an audio signal and optimizes the frequency and amplitude spectrum of the output signal to enhance bass perception. Whether you are limited by space, cost or implementation, for bass previously believed impossible. This process creates deep, rich bass in headphones and speaker systems that have poor or little bass response. Sub-woofer performance will be enhanced substantially. Unprecedented bass response will virtually eliminates the need for large speakers to create low frequency fundamental tones and will in several case eliminate the need for a sub-woofer all together. Be sure that the TRU BASS™ process will not color the midrange or create bass not present on recordings. This process will only define any bass present on a recording. ©American Audio® --Q-SPAND™ Instruction Manual Page 8 Q-SPAND™ CONTROLS AND FUNCTIONS 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 ©American Audio® - - Q-SPAND™ Instruction Manual Page 9 33. AC VOLTAGE SELECTOR - This switch is used to change the operating voltage. Operating voltage can be toggled between 120V/50Hz or 220V/60Hz. Always be sure the selector is set to the proper voltage for your area before attempting to operate the unit. 34. AC CONNECTION - This connector is used to supply main power to the unit via the included detachable power cord. Use only the supplied, polarized AC power cord. This cord is designed to fi t in one direction only. Do not attempt to force a cord if it does not fi t, be sure the cord is being inserted properly. 35. BALANCED XLR MASTER OUTPUTS - The Master Output includes a pair XLR Balanced JACKS as well as a pair RCA Unbalanced Jacks (38). The 3-pin XLR jacks send a high current balanced output signal. These jacks should be used when you will be driving an amp or other audio equipment with a balanced input, or whenever you will be running a signal line greater than 15 feet. Always, use these jacks whenever possible. 36. LIGHT CONTROL OUTPUT - This jack provides a preset mono audio output signal. There is no way to adjust this level, however this level will directly reflect the output level of the Channel Sliders (9). This buffered audio output should only be used with light controllers that can accept an external audio input signal. Great feature for Touch Panels and Chase Controllers. 37. PLAYER CONTROL - These jacks are used to control the “Q-Start” function between the mixer and a compatible American Audio CD Player. Input mini plugs from CD player controller into these jacks, input CD 1 into jack 1 and CD 2 into jack 2 and so on. 38. RCA MASTER OUTPUTS - The Master Output includes a pair XLR Balanced Jacks (35) as well as a pair RCA Unbalanced Jacks. The RCA jacks send a low current unbalanced output signal. These jacks should only be used for shorter cable runs to signal processors or looping to another mixer. For cable runs greater than 15 feet us...
Este manual também é adequado para os modelos :Instrumentos musicais - Q-SPAND (1.58 mb)