Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
This will cause no harm and may provide the sound you are looking for. 4.Blend With the B150 it is possible to blend your signal between a valve and/or solid-state input pre-amp section. Each type of pre-amp produces a different character of sound, valve pre-amps for example tend to give a very warm tone while solid-state pre-amps give a harder, snappier response, ideal for more percussive styles of bass playing. As these circuits are blendable, it is possible to have degrees of both types of pre-amp in your signal, to combine the best of both worlds. 5. Bass Turning the Bass control will effect the amount of low frequencies or bottom end in your bass guitar tone. Rotating this clockwise will increase the amount of lower tones generally making your bass sound deeper. Turning this control anti-clockwise will reduce the bass frequencies in your tone producing a reduction in bottom end thud. 6. Deep Switch Push switch to add extra bottom to the low end of the primary EQ. 7. Treble By adjusting the Treble control you can add or take away the higher frequencies in your bass tone. By increasing the amount of treble you will make your tone brighter, ideal for percussive styles of playing. 8. Bright Switch Push switch to add brightness and attack to the top end of the primary EQ. 9. Compressor The Compressor smoothes out your bass sound. As you increase the amount of compression, so you flatten out the peaks in the signal. 10. Compressor Active LED Indicates whether the Compressor is in operation. 11. 7 Band Graphic To allow you to further tailor your sound, with the Graphic it is possible to cut or boost 7 specific frequencies. If you do not want to alter the shape of your sound with the Graphic simply leave the sliders set to 0. 12. Limiter Traditional amplifiers when run at high volumes will begin to clip or distort. The Limiter facility when in use will prevent the power amp clipping at high volumes and at low volumes will have no effect. 13. Volume Controls the overall volume of the B150. - Effects Loop- An effects loop is used for connecting an external effects processor or floor pedal. The effects loop on the Marshall B150 is compatible with the output level of either type (processor or floor pedal) to ensure that a perfect match is made. 14. FX Send For connection to the input of an external effects processor or floor pedal. B150 5 GAIN E.Q. BASS TREBLE COMP Volume FX SEND FX RETURN LINE OUT LIMITER EARTH LIFT BRIGHT DEEP -15dB +15dB 0 80 Hz 160 Hz 320 Hz 640 Hz 1K 25Hz 2KHz ACTIVE PASSIVE Input 2.5KHz 0 10 Solidstate Valve -15 +15 -15 +15 0 10 0 10 BLEND D.I. Power POWER ON B150 GAIN E.Q. BASS TREBLE COMP Volume FX SEND FX RETURN LINE OUT LIMITER EARTH LIFT BRIGHT DEEP -15dB +15dB 0 80 Hz 160 Hz 320 Hz 640 Hz 1K 25Hz 2KHz ACTIVE PASSIVE Input 2.5KHz 0 10 Solidstate Valve -15 +15 -15 +15 0 10 0 10 BLEND D.I. Power POWER ON B150 GAIN E.Q. BASS TREBLE COMP Volume FX SEND FX RETURN LINE OUT LIMITER EARTH LIFT BRIGHT DEEP -15dB +15dB 0 80 Hz 160 Hz 320 Hz 640 Hz 1K 25Hz 2KHz ACTIVE PASSIVE Input 2.5KHz 0 10 Solidstate Valve -15 +15 -15 +15 0 10 0 10 BLEND D.I. Power POWER ON B150 Slap On Plectrum Fingers Plectrum Fingers Slap Off On On Off ENGLISH Suggested Settings Before we look at some suggested settings there are a couple of points that you should remember ; 1 / Taste in sound is a very personal thing. What might sound great to one bass player might not appeal to another bassist. Therefore these suggested settings may need some alterations to suit your own personal taste. 2 / One of the main influences on your sound will be your bass. Each bass displays certain tonal characteristics, some for example will sound brighter than others while others may sound bassier. For this reason again you may find that these suggested settings need some alteration to give the required sound. Here then follows three simple settings for the B150 for slap, fingers and plectrum styles. We hope that these settings provide you with a useful starting point to develop your own killer bass tones. Please Note : Gain and Volume should be adjusted to taste. ENGLISH 15. FX Return For connection from the output of an external effects processor or floor pedal. 16. Line Out The Line Out Jack can be used for connection to home recording equipment for direct recording. 17. D.I. Output with Earth Lift Switch The D.I. Output is designed for connection to professional recording or P.A. equipment. Connecting a piece of audio electrical equipment which has been earthed to another piece of earthed electrical equipment, such as an amplifier and recording equipment, can result in a background hum. Should this problem occur, the B150 features an Earth Lift Switch which when used will alleviate the hum. 18. Power Switch On/off mains power switch for the B150 with LED to indicate when on. B150 Rear Panel Features 1. Mains Input For connection to the mains. Always ensure that a good quality mains lead is used and that the plug is wired in accordance wit...
Este manual também é adequado para os modelos :Instrumentos musicais - BASS STATE B 150 (2.08 mb)
Instrumentos musicais - BASS STATE B 65 (2.08 mb)