Log:
Assessments - 4, GPA: 3.5 ( )

Instruções de Operação Yamaha, Modelo YBB-632S

Fabricante : Yamaha
Arquivo Tamanho: 9.73 mb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



por este dispositivo também tem outras instruções :

Facilidade de uso


After closing the valve cap, move the lever a few times to distribute the oil evenly. Valve oil Piston Rotor spindle oil Rotor spindle Backside of the instrument * Do not apply too much oil Receiver Rotor spindle Instrument’s front Rotor spindle oil * Do not apply too much oil Before You Play 25 3. Apply some lever oil to the lever shafts. Lever oil 4. While moving the levers, blow some air through the instrument to distribute the oil evenly. * Do not apply too much oil ¦ Assembling the Sousaphone Connect the bell to the body so that the bell is facing the same direction as the player’s face. 1. Loosen the bell screws. Firmly holding on to the bell on both sides, rotate the bell slowly while inserting the bell into the bell joint on the main body. After the bell is positioned, tighten the three bell screws so that each screw applies the same amount of pressure against the bell. Never loosen the screws on the copper bracing holding the main coils together. Doing so may cause the coils to separate resulting in injury. Also, regularly check that the attachment screws on the main tubing are tightened firmly. Completed assembly * During rests, make sure that the bell screws are tightened firmly. Bell joint receiver Bell screw Copper bracing Main coil Attachment screw Before You Play 26 ¦ Assembling the Leadpipe (Sousaphone only) The sousaphone uses a multi-piece leadpipe. This leadpipe in combination with a bit allows the player to adjust the mouthpiece to a comfortable position to best fit individual needs. 1. Apply some slide grease to the middle section of the leadpipe and then insert it into the leadpipe receiver. Next, tighten the screw on the receiver to secure the middle pipe in place. ¦ Assembling the Marching Tuba (Marching series only) The leadpipe on one of the marching series tuba models can be switched to convert the instrument between marching use and regular concert use. (An “M” at the end of the product number indicates a marching series tuba.) 1. Loosen screws A and B to remove the regular concert leadpipe, then attach the marching leadpipe and tighten screws A and B. A B C E D Bit Leadpipe Middle pipe Receiver Screw Leadpipe receiver Mouthpiece * If the bit is left on the leadpipe, it may become stuck in place. After playing, make sure that the bit is removed from the leadpipe and remove moisture from the bit. * The YSH-411 is supplied with two different bits. Both can be connected together if necessary. 2. Insert the square support on the backside of the instrument and use screw E to adjust the leadpipe angle, then tighten screws C and D to secure it. Concert leadpipe Marching leadpipe Backside Square support Before You Play * The marching type mouthpipe may become stuck or difficult to remove if left in the tuba. Please use caution. D 27 ¦ Setting the Mouthpiece Insert the mouthpiece until it just fits snugly and is no longer loose in the leadpipe. ¦ Tuning the Instrument Slide the main tuning slide in or out to tune the instrument...

Este manual também é adequado para os modelos :
Instrumentos musicais - YBB-105 (9.73 mb)
Instrumentos musicais - YBB-105S (9.73 mb)
Instrumentos musicais - YBB-201 (9.73 mb)
Instrumentos musicais - YBB-201S (9.73 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias