Assessments - 2, GPA: 5
(
)
)
|
Fotos e especificações Yamaha NS-P40 |
Facilidade de uso
Connection diagram Surround speakers Right Left ANTENNA FM GND AM COMPONENT VIDEO PR PB Y OPTICAL ( TV ) AV 1 AV 2 AV 3 AV 4 AV 5 AUDIO 1 AUDIO 2 COAXIAL (CD) COAXIAL OPTICAL VIDEO CENTERSURROUND HDMI 1 (BD/DVD) HDMI 2 HDMI 3 HDMI 4 FRONT COMPONENT VIDEO MONITOR OUT PR PB Y HDMI OUT MONITOR OUT AV OUT SUBWOOFER AU DIO OUT 75 SPEAKERS DOCK CENTERSURROUND FRONT SUBWOOFER SPEAKERS Center speaker Amplifier Note: The exact layout of the speaker terminals depends on your amplifier. Subwoofer To AC wall outlet ¦ Preparing the speaker cables Once you’ve positioned the speakers, you’ll need to cut the 24.5-meter (80 ft.) speaker cable to make five cables for connecting the two front speakers, center speaker, and the two surround speakers. 1 Cut the included speaker cable to suitable lengths for the front, center, and surround speakers. You need five cables. 2 Remove about 10 mm (3/8") of insulation from the end of each speaker cable. Right Left Front speakers 3 Twist the bare wires tightly. 10 mm (3/8") Good No Good Notes • Make the speaker cables as short as possible. Do not bundle or roll up excess cable. • Twist the bare wires tightly so the individual strands are not splayed. • Be careful not to injure yourself while preparing the speaker cables. 3 En English English ¦ Operating the speaker terminals Negative (–) 23311Positive (+) Note: Make sure the terminal is gripping the bare wire, not the insulation. 1 Press and hold the terminal tab. 2 Insert the bare wire. 3 Release the tab so that it closes securely on the bare wire, not the insulation. 4 Test the security of the connection by pulling gently on the cable. Notes • Make sure the bare wires do not touch each other, as this could damage the speaker or the amplifier. • If the connections are faulty, you will hear no sound from the speakers. ¦ Connecting the speakers Connect each speaker to the appropriate speaker terminals on your amplifier by using the cables you prepared earlier. See the “Connection diagram” on page 3 for reference. Make sure you connect the speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (–) terminals to negative (–) terminals. If you get them crossed over, the sound will be unnatural and lack bass. In your AV receiver’s speaker size settings, specify small (or “S”) for all of the NS-P40 speakers. If you’re connecting the subwoofer to a Yamaha DSP amplifier or AV receiver, connect to its SUBWOOFER or LOW PASS output. Connecting the power cables Once you’ve completed all of the speaker and subwoofer connections, plug the subwoofer, amplifier, and your other AV components into suitable AC wall outlets. Using the Subwoofer Rear panel 1 Power indicator Lights up when the POWER switch is set to ON; goes off when the POWER switch is set to OFF. 2 INPUT jack Input jack for connecting the line-level subwoofer output on your amplifier. 3 VOLUME control Adjusts the volume of the subwoofer. Turn it clockwise to increase the volume; counterclockwise to decrease the volume. 4 POWER switch Set this to ON to turn on the subwoofer. Set it to OFF to turn off the subwoofer. Setting the subwoofer volume The very first time you use the subwoofer, you need to set the volume balance between the subwoofer and the front speakers as follows. 1 Turn on your other AV components. 2 Set the subwoofer’s VOLUME control to minimum (0). 3 Set the subwoofer’s POWER switch to ON. The power indicator on the rear panel lights up. 4 Play a audio source that contains low- frequency bass sounds. Set the amplifier’s volume control to a suitable level. 5 Turn the subwoofer’s VOLUME control up gradually until you achieve a good balance between the subwoofer and the other speakers. Notes • Once the subwoofer volume has been set, you can leave the subwoofer’s VOLUME control set as it is and use your amplifier’s volume control to adjust the volume of the entire system. 4 En • If you replace the front speakers (NS-B40) with other speakers, you will need to re-adjust the subwoofer’s volume. Troubleshooting If this product doesn’t work as expected, look for a possible cause below. If the issue you are experiencing is not listed, or you cannot resolve it after reading through these instructions, disconnect the power cable and contact an authorized Yamaha dealer or service center. ¦ Front, surround speakers (NS-B40) and center speaker (NS-C40) Issue Possible cause Remedy There’s no sound. The speaker cables are not connected properly. Make sure the speaker cables are connected properly. The sound is very quiet. The speaker cables are not connected properly. Make sure the speaker cables are connected properly: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. ¦ Subwoofer (NS-SW40) Issue Possible cause Remedy The POWER switch is set to ON but the subwoofer doesn’t work. The power cable is not connected properly. Set the POWER switch to OFF, then make sure the power cable is connected properly. There’s no sound. The VOLUME control is s...
Este manual também é adequado para os modelos :Home theater - YHT-396 (1.95 mb)