Assessments - 5, GPA: 3.6
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
CHANNEL MESSAGE 4.2.2 PARAMETER CHANGE Command rx/tx function 8n NOTE OFF rx Control the internal effects 9n NOTE ON rx Control the internal effects Bn CONTROL CHANGE rx/tx Control parameters Cn PROGRAM CHANGE rx/tx Switch scene memories 2. SYSTEM COMMON MESSAGE Command rx/tx function F1 MIDI TIME CODE QUARTER rx Used when TIME REFERENCE is FRAME MIDI CLOCK. F2 SONG POSITION POINTER rx Used when TIME REFERENCE is MIDI CLOCK. 3. SYSTEM REALTIME MESSAGE Command rx/tx function F8 TIMING CLOCK rx MIDI clock FA START rx* Start automix (from the beginning) FB CONTINUE rx* Start automix (from the middle) FC STOP rx* Stop automix FE ACTIVE SENSING rx Check MIDI cable connections FF RESET rx Clear running status Received only when the Automix TIME REFERENCE setting is MIDI CLOCK. 4. EXCLUSIVE MESSAGE 4.1 Real Time System Exclusive Command rx/tx function F0 7F dd 06 MMC COMMAND tx MMC command (refer to MMC specification) F0 7F dd 07 MMC RESPONSE rx MMC response (refer to MMC specification) F0 7F dd 01 MIDI TIME CODE rx Used when TIME REFERENCE is MTC. 4.2 System Exclusive Message 4.2.1 Bulk Dump Command rx/tx function F0 43 0n 7E BULK DUMP DATA rx/tx BULK DUMP DATA F0 43 2n 7E BULK DUMP REQUEST rx/tx BULK DUMP REQUEST The following data types of bulk dump are used on the 02R96. Data name tx/rx function 'm' tx/rx Scene Memory & Request 'S' tx/rx Setup Memory & Request 'a' tx/rx Automix data & Request 'R' tx/rx Input patch library & Request 'O' tx/rx Output patch library & Request 'H' tx/rx Channel library & Request 'G' tx/rx Gate library & Request 'Y' tx/rx Compressor library & Request 'Q' tx/rx Equalizer library & Request 'E' tx/rx Effect library & Request 'J' tx/rx Bus to Stereo library & Request 'K' tx/rx Surround Monitor library & Request 'P' tx/rx Program change table & Request 'C' tx/rx Control change table & Request 'L' tx/rx User define layer & Request 'I' tx/rx Plug-in User define & Request 'V' tx/rx User define key & Request 'N' tx/rx Plug-in Effect Card Data & Request Command rx/tx function F0 43 1n 3E 0B PARAMETER rx/tx 02R96-specific parameter CHANGE change F0 43 3n 3E 0B PARAMETER rx/tx 02R96-specific parameter REQUEST request F0 43 1n 3E 7F PARAMETER rx/tx General purpose digital mixer CHANGE parameter change F0 43 3n 3E 7F PARAMETER rx/tx General purpose digital mixer REQUEST parameter request The following data types of parameter change are used by the 02R96. Type tx/rx function 1 tx/rx Edit buffer 2 tx/rx Patch data 3 tx/rx Setup data 4 tx/rx Backup data 16 tx/rx Function (recall, store, title) 17 rx Function (pair) 18 rx Function (event) 32 rx Key remote 33 tx/rx remote meter 34 tx/rx remote counter ** tx means that the data can be transmitted from the 02R96. rx means that the data can be received by the 02R96. Format Details 1. NOTE OFF (8n) Reception Received when the [Rx CH] matches. Used to control effects. STATUS 1000nnnn 8n Note off message DATA 0nnnnnnn nn Note number 0vvvvvvv vv Velocity (ignored) 2. NOTE ON (9n) Reception Received when the [Rx CH] matches. Used to control effects. STATUS 1001nnnn 9n Note on message DATA 0nnnnnnn nn Note number 0vvvvvvv vv Velocity (1-127:on, 0:off) 3. CONTROL CHANGE (Bn) Reception Received when [Control Change Rx] is ON and the [Rx CH] matches. However if [OMNI] is ON, this is received regardless of the channel. If [Control Change ECHO] is ON, these messages are echoed to MIDI OUT. If [TABLE] is selected, parameters will be controlled according to the settings of the [Control assign table]. The parameters that can be set are defined in the CONTROL CHANGE ASSIGN PARAMETER LIST. If [NRPN] is selected, four messages are used to control the defined parameter: NRPN control numbers (62h, 63h) and DATA ENTRY control numbers (06h, 26h). Parameter settings are defined in the CONTROL CHANGE ASSIGN PARAMETER LIST. Transmission If [TABLE] is selected, operating the parameters specified in the [Control assign table] will cause these messages to be transmitted on the [Tx CH] if [Control Change TX] is ON. The parameters that can be specified are defined in the CONTROL CHANGE ASSIGN PARAMETER LIST. If [NRPN] is selected, operating the specified parameters will cause data to be transmitted on the [Tx CH] if [Control Change TX] is ON, using four messages: NRPN control numbers (62h, 63h) and DATA ENTRY control numbers (06h, 26h). Parameter settings are defined in the CONTROL CHANGE ASSIGN PARAMETER LIST. 02R96—Manual de Instrucciones 278 Apendice C: MIDI 278 Apendice C: MIDI STATUS 1011nnnn Bn Control change DATA 0ccccccc cc Control number (0-95, 102-119) 0vvvvvvv vv Control value (0-127) If [NRPN] is selected STATUS 1011nnnn Bn Control change DATA 01100010 62 NRPN LSB 0vvvvvvv vv LSB of parameter number STATUS 1011nnnn Bn Control change *1 DATA 01100011 63 NRPN MSB 0vvvvvvv vv MSB of parameter number STATUS 1011nnnn Bn Control change *1 DATA 00100110 26 LSB of data entry 0vvvvvvv vv LSB of parameter data STATUS 1011nnnn Bn Control change *1, *2 DATA 00000110 06 MSB of data e...