Log:
Assessments - 3, GPA: 4 ( )

Instruções de Operação Crate Amplifiers, Modelo Triple 40/EFX

Fabricante : Crate Amplifiers
Arquivo Tamanho: 3.09 mb
Arquivo Nome : c70db4e4-a202-4560-963f-cb62c51b73da.pdf
Língua de Ensino: enesfrde
Ir para baixar



Facilidade de uso


Rotating this control clockwise will increase the amount of preamp distortion and sustain. (4 & 12) VOLUME This control, on both channels, sets the overall level of the respective channel. (5) BOTTOM This control‚ on the Ultra channel, varies the low frequency response of the amplifier. It is an active control (shelving type) and allows 15 dB of boost or cut. (6) BODY This control, on the Ultra channel, varies the mid frequency response of the amplifier. It is an active control (peak/notch type) and allows 15 dB of boost or cut. (7) EDGE This control, on the Ultra channel, varies the high frequency response of the amplifier. It is an active control (shelving type) and allows 15 dB of boost or cut. (8 & 16) Reverb This control sets the reverb level per channel. It works the same for both channels. (Note to Triple XXX 40 EFX owners: These controls are completely separate from the Digital Effects. Changing this control only affects the builtin spring reverb.) FRONT PANEL Triple XXX® 40 1 3 4 5 6 7 8 17 19 21 9 10 11 12 13 14 15 16 18 20 22 2 (9) Rhythm/Crunch Selector This button selects between the Rhythm and Crunch modes on the Triple XXX 40/EFX. The adjacent LED will illuminate when the Ultra channel is selected. (10) Rhythm/Crunch Channel Activation LED This LED‚ when illuminated‚ indicates selection of the Rhythm/Crunch channel and in which mode the channel is currently operating. The mode selector button (9) will determine which mode‚ Rhythm or Crunch‚ is active. (13) Bass This passive control regulates the low frequencies for the Rhythm/Crunch channel. (14) Mid This passive control regulates the mid frequencies for the Rhythm/Crunch channel. (15) Treble This passive control regulates the high or treble frequencies for the Rhythm/Crunch channel. (17) Volume Boost (Non EFX model only) This knob‚ allows you to set the level of the volume boost when yellow LED (18) is illuminated. (18) Volume Boost LED This LED illuminates when the Volume Boost (17) has been activated by the footswitch. (19) Channel Select Switch (Non EFX model only) This 2-position toggle switch allows selection between the Ultra and Rhythm channels. Channel switching can also be accomplished by footswitch. See the FOOTSWITCH section of this manual for explanation of switch operation. The CHANNEL SELECT SWITCH must be set in the Ultra position in order for the footswitch to operate properly. (20) Power Status Lamp This indicator illuminates when mains power is being supplied to the amp. (21) STANDBY SWITCH This two-way toggle switch allows the amp to be placed in the STANDBY mode. In the STANDBY position the tubes stay hot but the amplifier is not operational. Switching to the ON position places the amp in active mode. This switch should be turned on a few minutes after the power switch in order to warm up the tubes. (22) POWER SWITCH This two-way toggle switch applies mains power to the unit. The red power status lamp (20) will illuminate when this switch is in the ON position. This switch de-activates only one side of the mains‚ use caution when servicing. 6 7 (23) CHANNEL SELECT This switch selects the channel (Ultra or Rhythm). The active channel LED illuminates to indicate the active channel. (24) EFX ADJUST Pressing this control selects the effect. A yellow LED adjacent to the effect name will illuminate to indicate the selected effect. Rotating this control clockwise changes the parameter of the active effect according to the descriptions below. The surrounding LED ring indicates relative value of the parameter being adjusted. EFX ADJ PARAMETERS Tremolo: Rate increase Funk wah: Sensitivity increase Octaver: Wet/Dry mix Rotary Speaker: Rate increase Flanger: Rate increase Phaser: Rate increase Chorus: Rate increase/depth decrease EFX amps are built with factory settings loaded into the presets. To return to the factory settings, first turn the power to OFF. Then‚ press and hold both the EFX ADJUST (24) and DELAY (26) controls while turning the amp back on. (25) VOLUME BOOST This control adjusts the level of Volume Boost. The surrounding LED ring indicates level. (26) DELAY This control adjusts delay type, time, and volume. Three types of delay are available: SLAP (1 repeat), ECHO (3–4 repeats), or INFINITE (5–6 repeats). The LEDs in each section of the control indicate which type is active and level. Pressing the control twice sets the delay time to the interval between presses. Triple XXX® 40 EFX 23 24 25 26 8 REAR PANEL 28 34 29 30 31 32 33 Triple XXX® 40 EFX Triple XXX® 40 27 (27) Fuse A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, it should be taken to a qualified service center for repair. Warning: The fuse should only be replaced after the power cord has been disconnected. (28) Ground Polarity Switch This three-position, rocker-type switch should normally be placed ...

Este manual também é adequado para os modelos :
Instrumentos musicais - Triple 40/EFX (3.09 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias