Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Dist.) In this setup, you can directly record the eight analog inputs of the 01X (or up to 24 channels via the mLAN connection). Unless you’ve changed the settings, the 01X is set up for this operation by default. 1Connect the devices to be recorded to the 01X inputs. 2Adjust the input gain to match the output of the device. (p. 16) 6Set up the computer (with mLAN connection) and audio sequencer for recording. 1. Using the mLAN Auto Connector, make sure the number of channels (in “From 01X to PC/Mac”) is equal to or higher than the number of channels to be recorded. (Guide, pp. 9, 20) 2. Select the input channels of the mLAN Audio Driver on the sequencer. (p. 69) 3Apply effects, such as reverb, for monitoring purposes by adjusting the levels of Aux Send 3 (or individual channels and the Master layer (with (The effect is not recorded; only signal is.) 4Adjust the direct monitor level for channel to be recorded with the channel faders. This allows you to monitor without latency (delay). 5Adjust the output level with the STEREO fader and the MONITOR/PHONES knob. Effects can also be inserted in the signal path of each channel. Effect 1/2 PATCH = channel number (p. 102) You can also record the mLAN adjusting the output level (p. 91) DIRECT OUT POSITION Check that the input signal is not clipping or overloading from the horizontal level meter display on the 01X LCD. (p. 46) INPUT METER POINT = PRE EQ: input signal clip display You can bypass the EQ and Dynamics processing and send the signal direct to the mLAN output. DIRECT OUT Position = PRE EQ (p. 91) input signal clip Audio Sequencer Audio Track 01 Audio Track 02 Audio Track 03 Audio Track 04 Audio Track 05 Monitor 01X Computer EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan EQ, Dyn, Vol, Pan Effect 1, 2 Mix EQ, Dyn, Vol, Pan Synthesizer Synthesizer Synthesizer Mic Recording a Mix In this setup, you can record a mix of all 01X inputs, sending the stereo bus to mLAN Out. Ex. • Simultaneous recording of several MIDI tone generators with live instruments and microphones. • Mixing the individual outputs of a rhythm machine (with separate EQ and Dynamics on the 01X). Using Rec Bus Ex. 1: Use the Stereo Bus for monitoring the overall sound, and record via the Rec Bus. 1. Set Rec Bus to ON for the channel(s) you wish to record via RECBUS (Recording Bus Assign) = ON (p. 99) 2. Assign the Rec Bus output to mLAN. (p. 90) OUT PATCH (mLAN Out Channel): RECBUS = [1/2] Ex. 2: For vocal recording, monitor the overall separate monitor mix for the vocalist (microphone signal directly. 1. Set the Rec Bus output to ON for only monitor mix for the vocalist. 2. OUT PATCH (St/Aux Out Port) : RECBUS = ST/AUX OUT (p. 91) 3. Apply reverb or other processing Set the Rec Bus of the STI (See step #1 in Ex. 1 above.) 4. Record the microphone (See “Direct Recording” The Stereo Bus signal is sent to the mLAN output. ST-BUS > [1/2] in the OUT PATCH (mLAN Out Channel) (p. 90) In this situation, direct recording of channels 1 and 2 (as in “Direct Recording” above) is not possible. * In these explanations, page references Manual; those Guide. For more of Manual, diagram Quick Reference Audio Playback from the Computer/Sequencer (DAW) EQ, Dyn, Vol Ch. “mL2” (Layer 9-16) Pan Ch. “mL1” SEND3, 4 EQ, Dyn, Vol Effect 1, 2 Mix 01X ComputerAudio Sequencer Software Audio Mixer Monitor Monitor Monitor EQ, Dyn, Vol EQ, Dyn, Vol EQ, Dyn, Vol EQ, Dyn, Vol PanSEND3, 4 MIDI mLAN Audio Driver Ch.1, 2 STI1, 2Effect 1, 2 Mix OUT PATCH [ST-BUS] = D.OUT