Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
The antenna cables are designed to lay alongside the FCM and into the protective sleeve. Installing the card on top of these antenna cables may cause damage to your computer. NOTICE: Install the FCM in the WWAN slot. Do not install an FCM in the WLAN card slot. Doing so may cause damage to your computer. 4. Replace the keyboard cover (see Replacing the Keyboard Cover). Back to Contents Page Back to Contents Page Hard Drive Dell™ Inspiron™ 1420/Dell Vostro™ 1400 Service Manual Removing the Hard Drive Replacing the Hard Drive Removing the Hard Drive 1. Follow the procedures in Before You Begin. 2. Turn the computer over. 3. Loosen the two captive screws securing the hard drive cover and then remove the cover. 4. Remove the hard drive assembly using the pull-tab. 5. Remove the two screws securing the hard drive to the hard drive assembly. CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before working inside your computer, follow the safety instructions located in the Product Information Guide. NOTICE: To prevent data loss, turn off your computer (see Turning Off Your Computer) before removing the hard drive. Do not remove the hard drive while the computer is on, in standby mode, or in hibernate mode. NOTICE: Hard drives are extremely fragile; even a slight bump can damage the drive. NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell. 1 hard drive cover 2 captive screws (2) 1 hard drive assembly 2 pull-tab 6. Slide out the hard drive from the hard drive assembly. Replacing the Hard Drive 1. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. 2. Slide the hard drive in the hard drive assembly. 3. Tighten the two screws to secure the hard drive to the hard drive assembly. 4. Place the hard drive assembly in the hard drive bay by aligning the tabs on the hard drive assembly with the slots in the bay and pressing the connector end down. 5. Replace the hard drive door and tighten the screws. 6. Install the operating system for your computer, as needed (see "Restoring Your Operating System" in your Owner's Manual). 7. Install the drivers and utilities for your computer, as needed (see "Reinstalling Drivers and Utilities" in your Owner's Manual). Back to Contents Page 1 screws (2) 2 hard drive assembly 3 hard drive NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge" in the Product Information Guide). NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector. Back to Contents Page Keyboard Cover Dell™ Inspiron™ 1420/Dell Vostro™ 1400 Service Manual Removing the Keyboard Cover Replacing the Keyboard Cover Removing the Keyboard Cover 1. Follow the procedures in Before You Begin. 2. Open the display as far as it will open. 3. Insert a plastic scribe into the indent to lift the keyboard cover on the right side. 4. Ease the keyboard cover up, moving from right to left, and remove it. Replacing the Keyboard Cover 1. Insert the left edge of the keyboard cover. 2. Press from left to right until the keyboard cover snaps into place. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer. NOTICE: To avoid damage to the keyboard cover, do not lift the cover on both sides simultaneously. 1 keyboard cover 2 scribe Back to Contents Page Keyboard Dell™ Inspiron™ 1420/Dell Vostro™ 1400 Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard 1. Follow the procedures in Before You Begin. 2. Remove the keyboard cover (see Removing the Keyboard Cover). 3. Remove the two screws at the top of the keyboard. 4. Lift the keyboard and hold it up and slightly forward to access the keyboard connector. 5. Rotate the keyboard connector latch towards the front of the computer to disconnect the keyboard cable from the keyboard connector on the system board. 6. Slide the keyboard cable out of the keyboard connector. Replacing the Keyboard 1. Slide the keyboard cable into the keyboard connector. 2. Rotate the keyboard connector latch to secure the cable. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a conn...