Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Do not expose the battery to water. Do not expose the battery to heat. Do not store in locations where the temperature may exceed 40°C. Charge only at ambient temperatures between 4°C and 40°C. Charge only using the chargers provided with the tool. When disposing of batteries, follow the instructions given in the section "Protecting the environment". 11 ENGLISH Chargers Your charger has been designed for a specific voltage. Always check that the mains voltage corresponds to the voltage on the rating plate. Warning! Never attempt to replace the charger unit with a regular mains plug. Use your Black & Decker charger only to charge the battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage. Never attempt to charge non-rechargeable batteries. Have defective cords replaced immediately. Do not expose the charger to water. Do not open the charger. Do not probe the charger. The spotlight must be placed in a well ventilated area when charging. All batteries lose charge with time, specially when they are warm. Recharge the unit every two months for 24 hours when not in frequent use. If the unit is not going to be used for extended periods, disconnect the charger and store in a cool, dry place. Warning! Use only the supplied charger when charging the spotlight. The use of any other charger could damage the spotlight or create hazardous condition. The following symbols are found on your charger: Your charger is double insulated; therefore no earth wire is required. Read all of this instruction manual carefully. This appliance is intended for indoor use only 130oC The charger automatically shuts off if the ambient temperature becomes too high. As a consequence the charger will be inoperable. The charging base must be disconnected from the mains supply and taken to an authorised service centre for repair. This product must not be disposed of with normal household waste. Electrical safety Your charger is double insulated; therefore no earth wire is required. Always check that the main voltage corresponds to the voltage on the rating plate. Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized Black & Decker Service Center or an equally qualified person in order to avoid damage or injury. If the power cord is replaced by an equally qualified person, but not authorized by Black & Decker, the warranty will not be valid. FEATURES This appliance includes some or all of the following features: 1. Carry handle 2. 2 Position brightness switch (high and low setting) 3. Charging LED indicator 4. Carry lanyard 5. Trigger lock 6. Pistol grip 7. On/off trigger switch 8. Charging socket 9. Quartz halogen bulb 10. Charger jack plug 11. Mains charger adaptor Charging the spotlight (fig. A & B) This spotlight is shipped in a partially charged state. Charge the spotlight before first use using the mains charging adaptor (11) for 24 hours or until the green charging LED (3) lights. Charge after each use until the green charging LED indicator (3) lights. The LED (3) indicates the battery level whilst charging. One red LED indicates that the unit requires charging. Two red LEDs indicate a high level of charge remaining. The green LED lights shows the unit is fully charged. Charging with the mains charger (fig. B) Make sure that the spotlight is off (the trigger lock (5) is in the off position and the trigger (7) is not pressed). Note: To ensure optimum battery life do not charge for longer than 48 hours. Insert the charger jack plug (10) into the charging socket (8). Insert the mains charging adaptor (11) into a mains power socket. Charge until the green charging status LED (3) lights (approximately 24 hours). Note: Battery run-time is approximately 25 minutes on LOW setting and 18 minutes on HIGH setting. This run-time can be achieved only if the spotlight is fully charged, battery is in good condition and has been properly maintained. USE Before operating the spotlight remove the charger jack plug (10) from the charging socket (8). Operating the spotlight (fig. C) Move the trigger lock (5) to the unlocked position. To lock the trigger switch (7) in the on position, press the trigger switch (7) and push in the trigger lock (5). To shut the spotlight off, press the trigger (7) and move the trigger lock (5) to the unlocked position. Release the trigger (7). 12 ENGLISH High and low brightness switch (fig. D) To extend the run time of the spotlight the unit is fitted with a brightness switch (2). Slide the switch (2) forward towards the bulb to set the spotlight on high beam. Slide the switch (2) to the rear to set the spotlight on low beam (extended run time). Using the built-in carry lanyard The carry lanyard (4) may be used to store or carry the spotlight. Adjust the slide on the cords to keep the lanyard secure around the supporting object. MAINTENANCE Your Black & Decker tool has been designed to operate over a long period of time with a minimum of...
Este manual também é adequado para os modelos :Iluminação - BSL301 (5.24 mb)