Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Charge unit BEFORE first use using the 120 Volt AC Charger for20-30 hours or until the green Battery Status LED flashes. Charge after each use until green LED flashes. Charging/Recharging Using the 120 Volt AC Charger and a Standard HouseholdExtension Cord (not included) Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC Charger on theback of the unit. BATTERY STATUS LED INDICATOR BUILT-IN 120V AC CHARGER Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). Charge until the Battery Status LED Indicator green LED flashes (approximately 20-30 hours). DO NOT CHARGE FOR LONGER THAN 30 HOURS. Charging/Recharging Using the 12 Volt DC Charging Adapter Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port. 12 VOLT DC CHARGING ADAPTER 12 VOLT DC CHARGING PORT Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source. Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). Charge until the Battery Status LED Indicator green LED lights when the LED AREA LIGHTS pushbutton is pressed (approximately 3-4 hours). DO NOT CHARGE FOR LONGER THAN 4 HOURS. Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is 12 volt DC and is able to supply at least one half amp at 12 volt DC for 8 hours. This means a battery pack should be charged with at least 4 amp hours capacity. Note: When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the accessory outlet. WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY. OPERATING INSTRUCTIONS Operating the Spotlight 1. Disconnect from charger. 2. The ON/OFF trigger is located in the front of thepistol-grip handle of the spotlight. 3. To turn the spotlight ON, squeeze the trigger. 4. To turn OFF the spotlight, release the trigger. Note: The ON/OFF trigger can be locked in the OFF position using the trigger lock OFF switch on the side of theunit. Operating the LEDArea Lights The ON/OFF pushbutton for the LED Area Lights is located on the top of the Spotlight. ON/OFFTRIGGER TRIGGER LOCK OFF 4 SL202B_ManualEN_050107.qxp 5/1/2007 4:15 PM Page 5 Using the Built-In Carry Lanyard The Carry Lanyard may be used to store or carry the Spotlight. Adjust the slide on the cords to keep the Lanyardsecure around the supporting object. CARE AND MAINTENANCE All batteries lose charge with time, especially when they are warm. Recharge the unit every two months when not in frequent use, preferably using the 120 volt AC method. Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent. The quartz halogen bulb is the only user-replaceable part in the Spotlight. Periodically inspect the condition of adapters, connectors and wires. Contact Technical Support toll-free at 1-800-544-6986 to replace any components that have become worn or broken. Spotlight Bulb Replacement To replace the bulb, you will need a small Phillips screwdriver and a 12 volt H3 75 watt replacement bulb. Duringinstallation, avoid touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt orfingerprints on it. The bulb can be wiped clean with a cloth moistened with alcohol. RETAINING RING RUBBER “O” RING REFLECTOR RUBBER END CAP RUBBER BEZEL COVER TRIGGER (OFF) LOCK TRIGGER SWITCH QUARTZ HALOGEN BULB 1. Disconnect the unit from any charging adapters. 2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in theretaining ring. 3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside. 4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside. 5. Carefully remove the reflector and bulb assembly. BULB REFLECTOR HAIRPIN RETAINING WIRES PHILLIPS HEAD SCREWS 6. Disconnect the bulb wire from the red power wire. 7. Unsnap the hairpin retaining wires from the reflector’s flange. 8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need tocompletely remove this screw). 9. Lift out the bulb and detach wire. 10. Insert the replacement bulb into the reflector’s flange. 11. Put back and secure the hairpin retaining wires. 5 SL202B_ManualEN_050107.qxp 5/1/2007 4:15 PM Page 6 12. Connect the bulb power wire to the red power wire. 13. Tighten the retaining screw on the flange. 14. Place the reflector in position in the body of the spotlight. 15. Replace the rubber “O” ring in the groove around the perimeter of the reflector. 16. Replace glass and retaining ring so the screw holes are aligned. 17. Secure retaining ring with two screws. 18. Replace rubber bezel. 19. Operate switch to ensure...
Este manual também é adequado para os modelos :Iluminação - Power Series SL202B (222.44 kb)