Assessments - 4, GPA: 4 ( )

Fabricante : Dimplex Arquivo Tamanho: 6.72 mb Arquivo Nome : Língua de Ensino:

Only pull out the drawer when its time to refi ll the water tank or change a lamp, otherwise it may lead to excess water in the sump and reduced fl ame eff ect. If this happens empty the water from the sump as instructed under ‘Maintenance’. 2. With the flame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long than when it is at maximum fl ame setting. 3. Do not tilt or move the stove while there is water in the tank or sump. 4. Make sure that the stove is on a level fl oor. 5. The flame control knob ‘C’ Fig. 2 may be turned up or down to give a more realistic eff ect. 6. Sometimes the flames appear more real when the flame control knob is turned down. 7. Give the flame generator some time to react to changes you may make on the flame control knob. WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE Changing lamps. If a large amount of the smoke appears grey or colourless it may be that one or more lamps have failed. You can check for lamp failure as follows. 1. Leaving the fl ame effect on, open the doors fully, gently pull the drawer fully out by the tab. (See Fig. 3) 2. View the lamps from a distance in front of the stove and observe which lamp needs to be changed. 3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the stove from the mains. 4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them. 5. Remove the water tank by lifting upwards and place in a sink. 6. Remove the sump as described in the Cleaning Section. 7. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (See Fig. 4 and 5). Replace with a Dimplex Opti-myst, 12V, 50W, Gu5.3 base, 8° beam angle, coloured lamp. (Purchased from under the section ‘After Sales Service’, details of how to purchase the lamps are contained therein.) 8. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push firmly in place. (See Fig. 4 and 5). 9. Replace the Sump and water tank and carefully close the drawer and doors. 10. Switch on. Filling the water tank. When the water tank is empty, flame and smoke eff ect shuts off, and you will hear 2 audible ‘beeps’. Follow these steps to refi ll: 1. Open doors. 2. Press Switch ‘A’ to (0) (See Fig. 2). 3. Open the doors fully and gently pull out the drawer as far as possible by the tab. (See Fig. 3) 4. Remove the water tank by lifting upwards and outwards. 5. Place the water tank in sink and remove cap, Anti- clockwise to open. (See Fig. 6) 6. Fill tank with filtered tap water only. This is necessary to prolong the life of the flame and smoke producing unit. The water should be filtered through a conventional domestic water filter unit and the filter should be replaced regularly. 7. Screw the cap back on, do not overtighten. 8. Return the tank to the sump, with the tank cap facing down and the flat side of the tank facing outward. 9. Gently push the drawer back in as far as it will go. 10. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig. 2) 11. Press Switch ‘B’ once to turn on fl ame eff ect. (See manual control section and Fig. 2) - 3 Cleaning. WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE STOVE. We Recommend cleaning the following components once every 2 weeks, particularly in hard water areas:Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air fi lter. For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or fl uff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan stove. Water tank 1. Remove water tank, as described earlier, put into sink and empty water. 2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer groove and the centre rubber seal. 3. Put a small quantity of washing up liquid into the tank, refit the cap and shake well, rinse out until all traces of washing up liquid are gone. 4. Refill with filtered tap water only, replace the cap, do not overtighten. Sump 1. Press Switch ‘A’ to the ‘OFF’ (0) position 2. Gently pull the drawer out as far as possible. (See Fig. 3) 3. Remove the water tank by lifting upwards. 4. Disconnect the electrical connector, located on the left side of the sump, by first loosening the two retaining screws and gently withdrawing the connector. (See Fig. 8) 5. Release the lower sump locking tabs by turning 90°, this allows the sump to be lifted completely from its location. (See Fig. 9) 6. Gently lift up the sump assembly, taking care to keep level so as not to spill any water. Sit the assembly in the sink. (See Fig. 10) 7. Release the two upper sump locking tabs by turning 90°, then lift off the sump lid. (See Fig. 11) 8. Carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig. 12) 9. Put a small amount of washing up liquid i...

Baixe o seu

Para fazer o download, introduza 2 dígitos :