Log:
Assessments - 3, GPA: 3 ( )

Instruções de Operação Heartland, Modelo 8210

Fabricante : Heartland
Arquivo Tamanho: 153.79 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


For Model 9200 use 4 sheet metal screws and washers. To prevent chipping do not overtighten or use power tools. 5 WOOD STOVES ONLY STOVETOP Bracket -Place box on the floor close to stove. (See Fig. 1 Page 2). Machine screw Remove machine screws from the top (2 each side) Screwdriver -Remove the nuts, washers and screws located at rear edge of stove top (2 on SWEETHEART,4 on OVAL) and the 4 machine screws from the stove top. -With a helper, lift cabinet assembly from box by area that is circled. (See Fig. 1 Page 2). -Place cabinet assembly onto stove body. (See diagram above). -Line up holes in the bottom (foot) of the bracket with the stove top holes while one person supports cabinet, fasten the cabinet brackets to the stove with machine screws (2 each side). (See diagram above). -Re-insert screws from the inside of the lip at the back of stove through the splashback , then assemble the nuts and washers to each screw (2 on a SWEETHEART 4 on OVAL). Tighten nuts to a snug fit. To prevent chipping do not overtighten or use power tools. 6 GAS, ELECTRIC AND COMBINATION STOVES ONLY Deflector Back of cabinet Sheet metal 3 1/2" x 10" Exhaust adaptor screw If you are not venting outside, attach the deflector to the rear of cabinet with 4, sheet metal screws. If you are venting outside, attach the 3 1/2" x 10" exhaust adaptor with 4, sheet metal screws. Fasten your exhaust ducting to the adaptor. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) 7 Back of stove Back of stove Back of stove Back of stove CONNECTING POWER TO THE CABINET COMBINATION AND ELECTRIC SELF CLEAN OR STANDARD STOVES ONLY (SEE NEXT PAGE FOR GAS STOVES) After your exhaust hood has been installed the very last thing to do is to connect the multipin plug to the range. The receptacle is located at the rear of the stove by the main power cord. 5200, 5210, 4200, 4210, 6200, 6210, 8200, 8210, Exhaust Hood Recptacle Locations When installing the multi-pin plugs, make sure the flat sided pins are aligned with flat sided holes. Each plug is coded for proper fit. Do not force plug into receptacle. Insert themulti-pin plugs into corresponding receptacles- each plug is coded to match its receptacle. Loop power cord on back and attach power cord to stove back with supplied cable tie and screw Plug the stove into wall receptacle. Check all electrical functions of the cabinet (fan,light, clock, etc.) and check againthat ALL screws have been tightened before completeing the installation. 8 GAS STOVES ONLY Power In (male receptacle) Exhaust Hood In (female receptacle, from cabinet) Power In (male receptacle) Exhaust Hood In (female receptacle, from cabinet) Back of stoveBack of stove Model 9200 Model 7200 Exhaust Hood Receptacle Locations female receptacle male end of the cabinet power cord Models 7200, 9200 only After your exhaust hood has been installed, connect the plug to the range.The female receptacle for the exhaust h...

Este manual também é adequado para os modelos :
Placa - 1902 (153.79 kb)
Placa - 1903 (153.79 kb)
Placa - 620 (153.79 kb)
Placa - 6210 (153.79 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias