Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. BUILT TO LAST Wire Feed Arc Welder QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 Description This line of Campbell Hausfeld wire feed welders is designed to be used on standard 115V household current. The welders are equipped with infinite wire speed control to accurately select the proper wire feed rate needed for various welding conditions. Internal components are thermostatically protected. This welding system is designed for use with the Flux Core Arc Welding (FCAW) or the Gas Metal Arc Welding (GMAW) process. As delivered from the factory, this welder can weld with .024” (.6mm) to .035” (.9mm) diameter wire in MIG and .030” (.8mm) to .035” (.9mm) diameter wire in flux core. A starter spool of .035” (.9mm) flux core wire is included. Unpacking Welding accessories for the welder are packed inside the wire feed compartment. When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings and screws, etc. are tightened before putting unit into service. Report any missing or damaged items by calling 1-800-746-5641. CIRCUIT REQUIREMENTS This equipment ! CAUTION requires a dedicated 115 volt circuit. Refer to the following chart for correct circuit breaker or fuse rating. Do not run other appliances, lights or tools on this circuit while operating this equipment. Extension cords are not recommended. Blown fuses and tripped circuit breakers can result from failure to comply with this recommendation. 1 3 6 5 4 2 Figure 1 - Welder Components and Controls Heat Circuit Breaker or Selector Slow Blow Fuse Low 15 amp High 20 amp See page 7 for supply cable replacement instructions. COMPONENTS AND CONTROLS 1. Work Clamp - connect to work piece. 2. Wire Feed Gun 3. Power Cord - plug into 115 volt outlet. 4. On/Off Switch - illuminates if thermostat has automatically shut unit off. 5. Infinite Wire Speed Control - turn clockwise to increase wire speed and counterclockwise to decrease wire speed. 6. Heat Selector - Selects welding power. Four selections are possible; low 1, low 2, high 1 and high 2. General Safety ! DANGER Danger means a hazard that will cause death or serious injury if the warning is ignored. Warning means a ! WARNING hazard that could cause death or serious injury if the warning is ignored. Caution means a ! CAUTION hazard that may cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property. NOTE: Note means any additional information pertaining to the product or its proper usage. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2003 Campbell Hausfeld/Scott Fetzer For parts, manuals, product & service information IN971503AV 6/03 visit Wire Feed Arc Welder Always keep a fire extinguisher accessible while performing arc welding operations. Before starting or servicing any electric arc welder, read and understand all instructions. Failure to follow safety ! WARNING before use to avoid overheating and damage to insulation. Never immerse wire or wire feed gun in water. If welder becomes wet for any reason, be absolutely certain it is completely clean and dry before use! Always shut equipment off and unplug power cord prior to moving the unit. Always attach the work lead first. Verify work piece is securely grounded. Always shut off electric arc welding equipment when not in use and cut off ! DANGER and UV rays can cause injury to eyes and skin. Take all precautions described in this manual to reduce the possibility of injury to eyes and skin. All persons operating this equipment or in the area while equipment is in use, must wear protective welding gear including: welding helmet or shield with at least shade 10 lens, flame resistant clothing, leather welding gloves and full foot protection. Never look at arc welding operations without eye protection as described above. Never use a shade filter lens ! WARNING General Safety (Continued) MANUAL precautions or instructions can cause equipment damage and/or serious personal injury or death. . All installation, maintenance, repair and operation of this equipment should be performed by qualified persons only in accordance with national, state, and local codes. ! WARNING Improper use of electric arc welders can cause electric shock, injury, and death! Take all precautions described in this manual to reduce the possibility of electric shock. . Verify all components of the arc welder are clean and in good condition prior to operating welder. Be sure insulation on all cables, wire feed gun and power cord is not damaged. Always repair or replace ...
Este manual também é adequado para os modelos :Ditado - WG2040 (3.32 mb)
Ditado - WG2044 (3.32 mb)
Ditado - WG2045 (3.32 mb)