Log:
Downloads : 5   Arquivo Tamanho: 675 kb   Fabricante : Desa  
Categoria : Placa
@name

See Lighting Instructionson page 14. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to the REMOTE position. Note:The burners may light if handheld remote ON button was on when remote selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the remote selector switch in the REMO

Downloads : 0   Arquivo Tamanho: 675 kb   Fabricante : Desa  
Categoria : Placa
@name

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position. Pilot Burner Ignitor Electrode Figure 25 - Pilot No Control Options) 14 104461 Remote Selector Switch in Remote Position (Optional Remote Control) ON OFF REMOTE OFF PILOT ON LO IH ON OFF REMOTE OFF PILOT ON LO IH OWNER’S MANUAL OPERATING HEATER Continued TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Tu

Downloads : 4   Arquivo Tamanho: 146 kb   Fabricante : Desa  
Categoria : Placa
@name

You can also visit DESA’s technical service web site at 3. Align shim under adjusting plate as shown in Figure 1. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 1). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 1). 6. While firmly holding edges of trim together, tighten both screws on the adjusting plate using a slotted screwdriver. 7. Repeat steps 2 through 6 for other side. 8. Place the assembled trim

Downloads : 20   Arquivo Tamanho: 674 kb   Fabricante : Desa  
Categoria : Placa
@name

This is common with most heaters. If just after burner is lit or shut off tracting while cooling noise is excessive, contact qualified service person Heater produces unwanted odors 1. Heater burning vapors from paint, hair 1. Open window and ventilate room. Stop spray, glues, cleaners, chemicals, new using odor causing products while heater carpet, etc. (See IMPORTANT state-is running ment above) 2. Gas leak. See Warning statement at 2. Locate and correct all leaks (see Check- top of page ing Ga

Downloads : 1   Arquivo Tamanho: 945 kb   Fabricante : Desa  
Categoria : Placa
@name

weather stripping has been added on openable windows and doors and c. caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings. If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 6. If your home does not meet all of the three cr

Downloads : 2   Arquivo Tamanho: 1 mb   Fabricante : Desa  
Categoria : Placa
@name

This will only last a few hours. 1. STOP! Read the safety information, above. 2. Make sure equipment shutoff valve is fully open. 3. Turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, column 1. If you don’t smell gas, go to the next step. 5. Turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see

Downloads : 0   Arquivo Tamanho: 1 mb   Fabricante : Desa  
Categoria : Placa
@name

5. Install one plastic bushing provided in blower kit into the 1 1/2" hole in the left rear of firebox floor. Access hole through the rectangular opening in the rear panel (see Figure 15). 6. Remove the two blower mounting brackets from the rear panel by removing two screws each (see Figure 16, page 13). 7. Attach the two mounting brackets to blower housing using four screws provided in blower kit (2 for each bracket) (see Figure 16, page 13). Tighten screws securely. Place blower assembly tempo

Downloads : 43   Arquivo Tamanho: 804 kb   Fabricante : Desa  
Categoria : Placa
@name

Ventilation Air From Outdoors Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts. IMPORTANT: Do not provide

Downloads : 1   Arquivo Tamanho: 573 kb   Fabricante : Desa  
Categoria : Placa
@name

Side View Front View Top View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Front of Stove Unit Side Wall Side Wall 12 " Minimum 12 " Minimum 6" Minimum 48" Minimum Ceiling Floor Back Wall Corner Wall Wall 6 " Minimum 6 " Minimum Figure 4 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) Continued 104463 7 VENT-FREE NATURAL GAS STOVE HEATER INSTALLATION Continued STOVE CAVITY ASSEMBLY 1. Lift off corrugated box enclosing stove body crating. 2. Remove

Downloads : 3   Arquivo Tamanho: 2 mb   Fabricante : Desa  
Categoria : Placa
@name

Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur. Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 8, page 9). IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the





categorias