Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Press and holdthe DOWN ( ) button on the main unit for two secondsto initiate another signal search. PLACEMENT OF THE UNITS The main unit can be placed on any flat surface indoors. The remote sensor can be placed indoors or outdoors, ona flat surface or mounted on the wall. • Slide to the right the battery compartment door on the back of the unit and remove it. • Install 2 batteries (UM-3 or “AA” size 1.5V) matching the polarity as shown in the battery compartment. • Replace the battery compartment door. LOW BATTERY WARNING A low-battery indicator [ ] will appear next to theindoor or remote data reading line of the main unit warningthat the corresponding batteries need replacement. 9 10 11 The unit is in a searching mode. Temperature and humidityreadings are securely registered. No signals detected. --The indoor temperature and humidity with the icon IN are located below the remote temperature and humidityinformation line. NOTE: If the indoor or remote temperature or humiditygoes above or below operating range stated in specifications, the main unit’s display ( weather station portion) will showdashes "---" on the corresponding line. AUTO-SCANNING Press and hold the CHANNEL button for 2 seconds – the icon " " will appear on the main unit weather display above the COMFORT LEVEL indicator. All three remote channels data will be displayedone-by-one automatically with a 4 seconds delay in thefollowing sequence: Channel 1, Channel 2 and Channel 3. To exit from scanning mode, press and hold theCHANNEL button for 2 seconds, and the icon " " will disappear, returning the main unit weather display to thedefault display mode. REMOTE AND INDOOR TEMPERATURE & HUMIDITY The remote temperature and humidity information line islocated right below the weather forecast line of the mainunit’s display. The wave icon is located above the remote channel number indicates the reception status from the correspondingremote sensor. There are three following types of the reception statusmay be displayed: 12 PROGRAMMABLE TEMPERATURE ALARM This product allows manual programming of a HIGH and LOW temperature alarms for all three remote channels. Once the actual remote temperature will reach the pre-sethigh or low limits, the alarm will sound. The alarm can beset for temperature readings between -58 °F and 158°F. To program the temperature alarm for all remote channels, • Press the TEMP ALARM button once to enter into the Temperature Alarm Programming mode – the abbreviation "OF" will be displayed on the remote temperature line• Press and hold TEMP ALARM button until the lower temperature limit value (-58) will flash• Set the desired lower temperature limit using DOWN ( ) arrow button • Press TEMP ALARM button once confirming the lower temperature limit value• Press and hold TEMP ALARM button until the HIGH temperature limit value ( 158) will flash• Set the desired higher temperature limit using DOWN ( ) arrow button • Press TEMP ALARM button once confirming the higher temperature limit value 13 COMFORT LEVEL INDICATORS This product is capable of detecting and displaying thecurrent indoor comfort levels of surrounding environment. The comfort level is displayed on the weather stationportion of the main unit’s display. It is based on thecombination of the current indoor temperature andhumidity readings. There are following comfort levelsmay be displayed: COMFORT (comfortable); WET (wet) and DRY (dry) Indicator displayed Temperature Range Humidity Range Shows current condition COMFORT WET DRY 40%RH70% RH OVER 70%RH Below 40%RH Ideal for both relative humidity and temperature Contains excess moisture Contains inadequate moisture 20°C to 25°C (68°F to 77°F) -5°C to 50°C (23°F to 122°F) -5°C to 50°C (23°F to 122°F) 14 Forecast is... Sunny PartlyCloudy Cloudy Rainy When the display shows... Snowy NOTE: The weather forecast accuracy is approximately70%.The main unit display shows forecasted, notcurrent conditions. The SUNNY icon indicates clear weather, even when displayed during the night-time. MAXIMUM AND MINIMUM READINGS The maximum and minimum record of the indoor and remote temperature and humidity will be automaticallystored in the memory of the main unit (receiver). To display the minimum, maximum or the current reading press MEM button. If no button is pressed for the next 15 seconds, the unitwill return to the current temperature and humidity display. To clear the memory, press and hold MEM button for two seconds and all previously stored readings will be erased. WEATHER FORECAST This unit is capable of detecting the atmospheric pressurechanges. Based on collected weather data, it forecasts theweather for the next 12 to 24 hours. 15 LOST COMMUNICATION If the main unit display line for the remote sensor readinggoes blank, press and hold DOWN ( ) button for2 seconds to begin a new signal search. If the signal stillisn’t received, please make sure that: • The remote sensor is in its proper location. • The distance between main unit and remo...
Este manual também é adequado para os modelos :Estação Meteorológica - TC682EL (1.35 mb)