Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
The comfort level is displayed on the weather stationportion of the main unit’s display. It is based on thecombination of the current indoor temperature andhumidity readings. There are following comfort levelsmay be displayed: COMFORT (comfortable); WET (wet) and DRY (dry) Indicator displayed Temperature Range Humidity Range Shows current condition COMFORT WET DRY 40%RH70% RH OVER 70%RH Below 40%RH Ideal for both relative humidity and temperature Contains excess moisture Contains inadequate moisture 20°C to 25°C (68°F to 77°F) -5°C to 50°C (23°F to 122°F) -5°C to 50°C (23°F to 122°F) 14 Forecast is... Sunny PartlyCloudy Cloudy Rainy When the display shows... Snowy NOTE: The weather forecast accuracy is approximately70%.The main unit display shows forecasted, notcurrent conditions. The SUNNY icon indicates clear weather, even when displayed during the night-time. MAXIMUM AND MINIMUM READINGS The maximum and minimum record of the indoor and remote temperature and humidity will be automaticallystored in the memory of the main unit (receiver). To display the minimum, maximum or the current reading press MEM button. If no button is pressed for the next 15 seconds, the unitwill return to the current temperature and humidity display. To clear the memory, press and hold MEM button for two seconds and all previously stored readings will be erased. WEATHER FORECAST This unit is capable of detecting the atmospheric pressurechanges. Based on collected weather data, it forecasts theweather for the next 12 to 24 hours. 15 LOST COMMUNICATION If the main unit display line for the remote sensor readinggoes blank, press and hold DOWN ( ) button for2 seconds to begin a new signal search. If the signal stillisn’t received, please make sure that: • The remote sensor is in its proper location. • The distance between main unit and remote sensor(s) is not over 200 feet (60meters). • The path between units is clear of obstacles. Shorten the distance if necessary. • Fresh batteries are installed correctly in both remote sensor and main unit. If there is no reception, please perform the following steps: • Bring the main unit and remote sensor close together. • Remove four (4) small screws from the back of the remote sensor with small Phillips screwdriver, and open the battery compartment. • Remove the batteries from the battery compartment and reinstall them in the same manner. Remote sensor LED indicator will flash showing transmission of the signal. • Remove the batteries from the main unit and reinstall them in the same manner. • On the main unit select the same channel number using CHANNEL button as set on the remote sensor. The remote temperature and humidity appeared on the main unit’s display will show that transmission is being received successfully. 16 TRANSMISSION COLLISION Signals from the other household devices such as wirelessdoorbells, home security systems, and entry control, mayinterfere with this product or cause temporary receptioninterruption. This is normal and will not affect the generalperformance of the product. The transmission andreception of the temperature and humidity readings willresume once the interference subsides. ANALOG CLOCK DISPLAY Immediately after the battery installation, the clock’s hourand minutes “hands” will start moving and stop at 4:00,8:00 or 12:00 position. To program the desired time, • Press and hold the CLOCK SET button, located inside the battery compartment – the MINUTE and HOUR hands will start moving clockwise• Release the CLOCK SET button, once the MINUTE and HOUR hands have reached the desired time position. Immediately after releasing the CLOCK SET button, the SECONDS hand will start moving, confirming that clock is started. ALARM To set the time alarm, • Turn the ALARM knob, moving the ALARM hand (smallest from three) to the desired alarm time• Release the ALARM knob • Slide ON/OFF switch to the ON position DISABLING THE ALARM Slide the ON/OFF switch on the main unit to the OFF position disabling the clock’s alarm. SNOOZE When the time alarm sounds, press the SNOOZE/LIGHT button to temporarily stop it. After the SNOOZE/LIGHT is depressed, the time alarm sound will resume in four minutes. If the alarm is not disabled after that, it will sound for twomore minutes and then will stop by itself. 17 BACKLIGHT The backlight feature is enabled only after the time is set. To activate the backlight press the SNOOZE/LIGHT button once, and both – clock and weather station displays -willlight up for five seconds. PRECAUTIONS • This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • Do not immerse the units in water. • Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits. • Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts. •...
Este manual também é adequado para os modelos :Estação Meteorológica - TS33C (1.35 mb)