Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
If the signal still isn’t received, please make sure that: • The remote sensor is in its proper location. • The distance between main unit and remote sensor is not over 100 feet (30meters). • The path between units is clear of obstacles. Shorten the distance if necessary. • Fresh batteries are installed correctly in both remote sensor and main unit. 11 If there is still no communication, please perform thefollowing steps: • Bring the main unit and remote sensor close together. • Remove four (4) small screws from the back of the remote sensor with a small Phillips screwdriver, and open the battery compartment. • Remove the batteries from the battery compartment and reinstall them in the same manner. Remote sensor LED indicator will flash showing transmission of the signal. • Remove the batteries from the main unit and reinstall them in the same manner. • The remote temperature appearing on the main unit’s display will show that the transmission is being received successfully. TRANSMISSION COLLISION Signals from other household devices such as wirelessdoorbells, home security systems, and entry controlmay interfere with this product or cause temporaryreception interruption. This is normal and will not affectthe general performance of the product. Thetransmission and reception of the temperature readingswill resume once the interference subsides. PRECAUTIONS This product is engineered to give you years of satisfactoryservice if handled carefully. Here are a few precautions: • Do not immerse the units in water. • Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits. • Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts. • Do not tamper with the units internal components. Doing so will invalidate the warranty and may cause damage. These units contain no user-serviceable parts. 12 SPECIFICATIONS Main Unit Indoor TemperatureProposed operating range: -5.0°C to +50.0°C/23.0°F to 122.0°F Temperature resolution: 0.1°C/0.2°F User-selectable (F° or C°) temperature display Low battery indicatorWall Mount or Desktop option Remote Sensor Remote TemperatureProposed operating range with alkaline batteries: -20.0°C to + 70.0°C/-4.0°F to + 158°F Proposed operating range with lithium batteries: -38.8°C to + 70.0°C/-38.0°F to +158°F Temperature resolution: 0.1°C/0.2°F Low battery indicatorRF Transmission Frequency: 433 MHzMaximum number of remote sensors: 3 (one included) RF transmission range: Maximum 100 feet (30 meters) Temperature transmission cycle: approximately 45 seconds Power Main unit: 2 AA size (UM-3) 1.5V batteries (not included) Remote Sensor: 2 AA size (UM-3) 1.5V batteries (not included) Dimensions Main unit: 2.89(L) x 3.64(H) x 1.47(D) inchesRemote sensor: 2.37(L) x 4(H) x 1(D) inch • Use only fresh batteries. Do not mix new and old batteries. • Read the user's manual thoroughly before operating the units. 13 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modification to this unit not expresslyapproved by the party responsible for compliance couldvoid the user’s authority to operate the equipment. NOTE: This equipment had been tested and found to complywith the limits for a Class B Digital device, pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation. This equipment, installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. There is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmfulinterference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouraged to improve or correct turning the interferenceby one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 14 DECLARATION OF CONFORMITY We Name: Hideki Electronics, Inc. Address: 7865 SW Mohawk, Tualatin, OR 97062Telephone No.: 1-503-612-8395 declare that the product Product No.: TM004 Product Name: In/Out Thermometer with Remote SensorManufacturer: Hideki Electronics Ltd. Address: Unit 2304-06, 23/F Riley House, 88 Lei MukRoad, Kwai Chung, New Territories, Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cau...
Este manual também é adequado para os modelos :Estação Meteorológica - TS03C (602.18 kb)