Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Your Precision Wash System® dishwasher uses energy efficient motors for the wash and drain portions of the cycle you select. Each cycle has a series of water fills and drains for washing and rinsing dishes. As each cycle begins, you may–or may not– hear the drain motor. The next sound you will hear is the splashing water as it enters the tub. Then the lower arm rotates and circulates water. This is followed by a pause and a slightly different sound as the middle arm sprays water. If you listen closely, you will hear the change in sound as the wash action switches from one arm to the other. PLEASE BE ADVISED: If you compare this dishwasher to previous models, you may be surprised at what you DON'T hear! Appearance may vary from your model. Getting Started 1. Load dishwasher (See Preparing and Loading Dishes). 2. Add detergent (See Dishwasher Dispenser & Detergents). 3. Add rinse aid, if needed (See Rinse Aid). 4. Close door to latch. 5. Select desired CYCLE (See Cycle Chart). The indicator light above the pad will glow when selected. 6. Select desired OPTIONS (See Energy Options). The indicator light above the pad will glow when selected. 7. Run hot water faucet nearest dishwasher until water is hot. Turn water off. 8. To start, press START/CANCEL pad. Note: The dishwasher is programmed to remember your last cycle so you do not have to reset each time. To start the dishwasher using the same cycle and options selected on the previous wash, just press the START/CANCEL pad. Wash Cycle Selections Note: Cycle times are approximate and will vary with options selected. Hot water is necessary to activate dishwasher detergent and melt fatty food soils. An automatic sensor will check the incoming water temperature and, if it is not hot enough, the timer will be delayed for automatic water heating in the main wash of all cycles. This happens even when HI-TEMP WASH option has not been selected. When HITEMP WASH is selected, an even higher temperature will be guaranteed to handle heavier soil loads. 4 Operating Instructions (continued) Cycle Chart Cycle To Select Cycle Water (approx.) Time* (min.) Washes/ Rinses For pots, pans, casseroles and dinnerware with dried-on or baked-on soils. Pots Pans Select POTS PANS and desired OPTIONS. HI-TEMP WASH and SANITIZE will automatically be provided. gal.8.5 105 2 washes 5 rinses For regularly soiled dishes and silverware. Normal Wash Select NORMAL WASH and desired OPTIONS. gal.6.1 85 2 washes 3 rinses For lightly soiled and pre-rinsed dishes and silverware. Light Wash (Both Racks) Select LIGHT WASH (BOTH RACKS) and desired OPTIONS. gal.4.9 75 1 wash 3 rinses For lightly soiled and pre-rinsed dishes and silverware when you do not have a full load. Light Wash (Upper Rack) Select LIGHT WASH (UPPER RACK) and desired OPTIONS. gal.3.7 65 1 wash 2 rinses Options Selections Hi-Temp Wash When HI-TEMP WASH option is selected, the dishwasher heats water in the main wash to approximately 140°F (60°C). This increase in water temperature helps dishwasher detergent remove food grease and soil from dishes more effectively and aids in drying. HI-TEMP WASH option can be used with all cycles. When HI-TEMP WASH option is selected, the light above the pad will come on and remain on until end of cycle. To turn off the HI-TEMP WASH option, press the pad a second time. The light above the pad will turn off. Sanitize Option To sanitize your dishes and glassware, select the SANITIZE option. When selected, the light above the pad will come on and remain on until end of cycle. The water temperature in the final rinse will be raised to 150°F (66°C) and will maintain that temperature for 9 minutes. This option is available in Pots Pans, Normal and Light (Both Racks) cycles. Only these sanitization cycles have been designed to meet NSF requirements. * Includes dry time. The cycle time will be extended until the proper water temperature is reached.Washing action will continue during the water heating delay. For best results, the incoming water temperature should be at least 120°F (49°C). The sanitize criteria may not be satisfied if there is an interruption of the cycle, power failure, or if the incoming water temperature is below 120°F (49°C). To turn off the SANITIZE option, press the pad a second time. The light above the pad will turn off. Heat Dry/No Heat Dry Option HEAT DRY OFF option saves electricity since the heating element is off during drying portion of cycle. When selected, the light above the pad will come on and remain on until end of cycle. To speed the drying process, open the door slightly after the cycle is complete. Some water droplets may remain on door and tub and in areas where dishes touch silverware basket and rack. 5 Operating Instructions (continued) To select heated dry, press the pad a second time. The light above the pad will turn off. Heated dry provides faster drying since the heating element is on during the drying portion of the cycle. You may see water vapor coming from vent du...
Este manual também é adequado para os modelos :Máquinas de lavar louça - 950 Series (621.54 kb)
Máquinas de lavar louça - 950 Series (621.54 kb)
Máquinas de lavar louça - 950 Series (621.54 kb)
Máquinas de lavar louça - 950 Series (621.54 kb)