Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Refer to page 27 for information on how to remove these spots. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH 19 RINSE AID DISPENSER Eurotech dishwashers are designed to use liquid rinse aids in hard water areas. The rinse aid dispenser is located inside the door next to the detergent dispenser. The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes that can leave spots and streaks. It also improves drying by allowing water to “sheet” off the dishes. To fill the rinse aid dispenser, follow the steps below. 1. Open the dispenser by turning the cap to the left then lift it out. 2. The dispenser holds about four ounces of liquid rinse aid. Pour the rinse aid into the dispenser until the level indicator turns completely black, being careful not to overfill. (Overfilling could cause the dishwasher to oversuds.) 3. Wipe away any spills with a damp cloth. 4. Replace the cap by turning it to the right until it stops. It’s a good idea to give the cap a tug to make sure it’s secure. If you have soft water, rinse aid may cause a white film to develop on your dishes. If this happens, you may not need rinse aid. ADJUSTING THE AMOUNT OF RINSE AID DISPENSED A measured amount of rinse aid is released during the final rinse. As with detergent, the amount of rinse aid needed for your dishes depends on the hardness of the water in your area. (See previous page.) Too much rinse aid can result in lather or foaming and cause cloudiness or streaks on your dishes. If the water in your area is very soft, you may not need rinse aid. If you do, you can dilute the rinse aid with an equal amount of water. The rinse aid dispenser has four settings. Always start with the dispenser set on “1.” If spots and poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser lid and rotating the dial to ”2.” If the dishes still aren’t drying properly or are spotted, adjust the dial to the next higher number until your dishes are spot-free. WHEN TO REFILL THE RINSE AID DISPENSER The black dot on the rinse aid dispenser indicates the amount of rinse aid in the dispenser. As the rinse aid diminishes, the size of the black dot decreases. You should never let the rinse aid get below one-quarter full. RINSE AID INDICATOR LIGHT Models EDW254E, EDW274E, and EDW294E have a rinse aid indicator light on the control panel that comes on when the dispenser is empty. After you refill the dispenser, the light will continue to glow until the program is complete. MODEL EDW242C OPERATING INSTRUCTIONS CONTROL PANEL Programs On / Off 1 2 3 4 PROGRAMS START 4 Pots & Pans 3 Normal 2 Light 1 Soak & Hold ON On / Off Button Program ButtonIndicator program lights Start Button ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH ON/OFF BUTTON Press the this button, “The LED corresponding to the last wash cycle performed lights up” INDICATOR PROGRAM LIGHTS The ON lights indicate which cycle is currently in progress. PROGRAM BUTTON When you press the button for the first time, you confirm the wash cycle that corresponds to the flashing LED. The next time you press the button, the LED of the program that corresponds to the wash cycle you intend to select will light up. At the end of the cycle, the selected program flashes.Select the program which you believe is best suited to the types of dishes which need to be washed. START BUTTON Press button with the appliance door shut, the wash cycle will start and the LED on the button itself will light up. EDW242C PROGRAMS INDICATOR “ON” LIGHTS The light to indicate the power is on. CANCELLING A PROGRAM To modify a wash cycle in progress, you must press the Start button for approximately 6 seconds; subsequently, the LED of the selected program begins to flash. The RESET phase will end when the Start button LED goes off. At this point, the appliance is ready to be set again. If you forget to put a dish in, you can interrupt the wash cycle (preferably only if it hasn’t been running for long) by pressing the Start button which then flashes; open the appliance door and place the dish inside. To restart the appliance, close the door and press the Start button again; the cycle will resume from the point in which it was interrupted. To repeat the same cycle, press the program button and then the Start button. Before you restart the unit, make sure the detergent dispenser is still closed; otherwise, you will have to add detergent. (Please note that if the program has run beyond the fill phase, the water will be pumped out.) Wash Wash Temps (° F) Rinse Temp (° F) Recommended LoadsProgram Normal Soak (& hold) House For extra-heavily soiled loads that require a presoak, such as pans or baked-on casseroles Light 105 105 Light soiled loads Normal 130 130 Normally soiled loads Pots & Pans 150 140 Heavily soiled loads, such as pans or casseroles 21 MODEL EDW254E OPERATING INSTRUCTIONS CONTROL PANEL Program Knob LCD Window Indicator Lights Delay Start Start Top Load ON/OFF BUTTON Pre...
Este manual também é adequado para os modelos :Máquinas de lavar louça - EDW254E (893.36 kb)
Máquinas de lavar louça - EDW274E (893.36 kb)
Máquinas de lavar louça - EDW294E (893.36 kb)