Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance. This is achieved by using dishwasher salt. To add dishwasher salt, follow the steps below: 1. Remove the lower dishwasher basket and then unscrew the salt compartment cap. 2. Fill the compartment with dishwasher salt (do not use table salt), carefully to prevent unnecessary spillage. Before first use, you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water (up to the brim of the compartment) as shown in figure 3. 3. Replace the cap and the lower basket. When the salt warning light on the control panel illuminates, you should refill the salt compartment with salt only – do not add water to the salt compartment after the first use. You should run a programme immediately after adding dishwasher salt, to prevent any damage to the dishwasher systems. fig. 1 fig. 2 fig. 3 Softener Adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water harness level of your water supply contact your local water board. To set the softener adjustment system unscrew the cap from the salt container and rotate the ring indicated in figure 4 according to the table below. Water Hardness Level Clarke degrees .dH mmol/l Selector position Salt c o n s u m p t i o n (Grams/cycle) Autonomy(cycles/2kg) 1 2 0 -14 0 -17 0 -1,7 1,8 -4,4 18 -44 14 -36 / "-" /0 20 60 3 36 -71 45 -89 4,5 -8,9 MED 40 40 4 > 89 > 71 > 8,9 "+" 60 25 fig. 4 Rinse Aid To fill the rinse aid compartment 1. Open the rinse aid compartment by turning and removing the cap as shown in figure5. 2. Fill the rinse aid compartment until the rinse aid indicator goes dark, as shown in figure 6 (where “a” indicates the compartment is empty, and “b” indicates the compartment is full). 3. Replace the cap, ensuring the markers on the cap line up with the compartment prior to screwing the cap back in place. Rinse Aid Adjustment The level of rinse aid use is preset to 3. You can adjust the level of rinse aid use by adjusting as shown in figure 7. If water stains form on the dishes after a wash, the level should be increased. If blue stains which can be wiped away are left on the dishes after a wash, the level should be decreased. Please note: Rinse aid ensures better quality wash results and increased drying performance. fig. 5 fig. 6 fig. 7 General Information To adjust the height of the upper basket: • Open the basket retaining clips, as shown in figure 8, by turning them to the side. • Remove the upper basket, and relocate the alternate set of wheels on the runner, as shown in figure 9, pushing the basket back into place. • Close the basket retaining clips. • The images below are designed as guidance as to best practice for loading the dishwasher. Information on reference tests implemented in compliance with EN 50242 Appliance loaded in accordance with standard specifications. Example of loaded dishwasher: See below. Capacity: 9 place settings Reference programme: Light wash Rinse-aid setting: 5 fig. 8 fig. 9 Detergent: 5g+22g Height-adjustable top-basket must be fitted in the uppermost position. If the reference tests do not comply fully with EN 50242, e.g., degree of soiling, type of dishes and cutlery, etc., contact the appliance manufacturer before starting the test. Upper basket Lower basket Technical Information Width 44.6 cm Depth 55 cm Height 82 cm Capacity 9 standard place settings Mains water pressure 0.03-0.6 MPa Power voltage 220-240V ~50 Hz Rated current input 10 A Total absorbed power 1950 W Programme Listing Programme names and temperatures Intensive 70O wash Normal 55O wash Economic 50O wash Glass 45O wash Rapid wash 40O wash Prewash No heat Level of soil High Medium Medium Small Small NA Detergent amount A=Main B=Prewash A+B A+B A+B A A NA Hot prewash 70O wash Cold rinse Hot rinse Dry End Cold prewash 55O wash Cold rinse Hot rinse Dry End Cold prewash 50O wash Cold rinse Hot rinse Dry End 45O wash Warm rinse Hot rinse End Prewash End 40O wash Cold rinse End Dry Programme duration (mins.) standard/ quick 112/94 102/90 162/140 92/82 32/28 12/12 Electricity consumption (kW hours) standard/ quick 1.36/1.25 1.00/0.93 0.80/0.76 0.75/0.65 0.27/0.24 0.02/0.02 Water consumption (litres) standard/ quick 18/16 15/14 14/13 12/10 9/8 3/3 The values and times provided above have been obtained under laboratory conditions according to relevant standards. This information can change depending on the conditions of the dishwasher’s use and environment. (mains supply voltage, water pressure, water input temperature and environment temperature). Laboratory measured value in accordance with European standard EN50242 Care and Maintenance Before beginning any care or maintenance, you shou...
Este manual também é adequado para os modelos :Máquinas de lavar louça - WC430 (1.01 mb)
Máquinas de lavar louça - WC430 (1.01 mb)