Right to Left . Left to Right VOLTAGE . 208/60/1 . 240/60/1 . 380/60/3 . 208/60/3 . 240/60/3 . 480/60/3 . 600/60/3 MODEL . CL54e – Dishwasher OPTIONS AT EXTRA COST . Stainless steel pressure-less 15 KW or 30 KW booster heater . Higher than standard chamber ACCESSORIES . Stainless steel vent hoods . Direct drive unloader . Side loader . Blower-dryer . Drain water tempering kit Specifications, Details and Dimensions on Inside and Back. CL54e DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOB

Start the machine momentarily and verify proper direction of rotation. Electric Heat Connect a permanent electrical power supply to the line terminals of the control box. The tank water temperature is regulated by a solid-state thermostat which is preset at the factory and should not require adjustment. If an adjustment is necessary or the machine is to operate low temperature, contact your local Hobart service office. Use the machine thermometers for verification of proper water temperatures. –

O (Feb. 2006) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORTANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS

Electrical components are wired with type ST cord. Line disconnect switch NOT furnished. CYCLE OPERATION: The microcomputer-timing program is started by closing the doors, which actuates the door cycle switch. The microcomputer energizes the wash pump motor contactor during the wash portion of the program. After the wash, a dwell permits the upper wash manifold to drain. At the end of the dwell, the final rinse solenoid valve is energized. After the final rinse valve closes, Sani-Dwell (Hot Wate

FT-800 SERIES DISHWASHER FOOD EQUIPMENT • Water and energy saving design through reduced water and tank heat usage and automatic pump shut down control through conveyor. • Common water, drain, electric and steam connections. • Exclusive load end flush system. • Built-in integral wiring channel. • Automatic temperature control and positive low-water heater and pump seal protection. • Built-in inherent motor overload protection with manual reset. • Built-in vent ducts—dampers and drip control. • I

11). NOTE: DO NOT use Teflon tape on gas line pipe threads. For gas line pipe connections, use LOCTITE 565, Hobart part 546292, or a flexible sealant suitable for use with Natural and Propane Gases. The appliance and its gas connections must be leak tested before placing the appliance in operation. Use soapy water for leak test. DO NOT use open flame. The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition). C

A fused disconnect switch or circuit breaker must be installed in the electrical service line supplying this dishwasher and should meet the requirements of your local electrical code. The incoming power supply connections should be made to the terminal block in the control box and a ground lead should be connected to the grounding lug in the control box if grounding is not provided by the conduit used. When equipped with single point electrical connection option for both the dishwasher and elect

Regulated power infrared gas immersion tube system is optional at extra cost. A solid-state igniter board controls the gas valve and provides flame ignition. A transformer steps the control circuit voltage down to 24 volts to power the igniter board and gas valves. Gas Heated Dishwasher: For natural gas, gas pressure (customer connection) not to exceed 7" W.C. For liquefied petroleum, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C. natur

Water hardness recommended to be 3 gr. for best results. Automatic interlocks shut off pump and conveyor if door is opened when machine is in operation. CONSTRUCTION: Tank, chamber, frame, legs, control box, doors, and all panels are constructed of stainless steel. PUMP: Two 165 gpm recirculating stainless steel pumps and impeller with a ceramic seat seal. Easily accessible pumps assembly permits quick inspection. The pumps are self-draining. All piping distributing water to the upper and lower

6) Repeat steps 4 and 5 for each digit. a. After pressing ENTER on the fourth digit, you will immediately return to the ENTER SECURITY CODE? screen. 7) You will know you entered the code correctly if the letter in the lower left corner reads M. Refer to Machine Operation and Programming Security Levels on page 15 for more details on other letters that may appear. a. If it does not match, repeat steps 3 through 7. b. If it does match, continue to step 8. 8) Press the UP or DOWN keys repeatedly un