Assessments - 3, GPA: 3 ( )

Fabricante : American Standard Arquivo Tamanho: 372.24 kb Arquivo Nome : Língua de Ensino:

(66 Kg.) 895 Lbs. (406 Kg.) 90 Gal. (341 L) 40 Gal. (151 L) 55-1/2 x 28-3/4 In. (1410 x 730mm) 62 x 49-3/4 In. (1575 x 1264mm) 13-3/8 In. (340mm) 25 Lbs./Sq.Ft. (123 Kgs./Sq.m) 27.552ELECTRICAL SPECIFICATIONSINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWMIN. OPERATING GAL. BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA) PTS. CUBE (FT3) 1.4 HPR, 9.7 AMPS, 120V.PUMPGENERAL SPECIFICATIONS FOR 237172 x 36 x 21-3/4 In.(1829 x 914 x 552mm) 100 Lbs. (45 Kg.) 625 Lbs. (283 Kg.) 63 Gal. (238 L) 47 Gal. (178 L) 54 x 19-1/4 In. (1372 x 489mm) 63-1/4 x 29-1/2 In. (1607 x 749mm) 15-1/2 In. (394mm) 35 Lbs./Sq.Ft. (169 Kgs./Sq.m) 17.238ELECTRICAL SPECIFICATIONSINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWMIN. OPERATING GAL. BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA) PTS. CUBE (FT3) 1.4 HPR, 9.7 AMPS, 120V.PUMPGENERAL SPECIFICATIONS FOR 238372 x 42 x 25-1/2 In.(1829 x 1067 x 648mm) 100 Lbs. (45 Kg.) 841 Lbs. (382 Kg.) 89 Gal. (337 L) 41 Gal. (155 L) 48 x 26-1/2 In. (1219 x 673mm) 60-3/4 x 35-3/4 In. (1543 x 908mm) 18-1/2 In. (470mm) 40 Lbs./Sq.Ft. (196 Kgs./Sq.m) 17.248ELECTRICAL SPECIFICATIONSINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWMIN. OPERATING GAL. BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA) PTS. CUBE (FT3) 1.4 HPR, 9.7 AMPS, 120V.PUMPGENERAL SPECIFICATIONS FOR 246672 x 54 x 23-1/4 In.(1829 x 1372 x 591mm) 130 Lbs. (59 Kg.) 1213 Lbs. (550 Kg.) 130 Gal. (492 L) 92 Gal. (348 L) 50 x 42 In. (1270 x 1067mm) 64-1/2 x 43-3/4 In. (1638 x 111mm) 15-1/2 In. (394mm) 45 Lbs./Sq.Ft. (219 Kgs./Sq.m) 27.562ELECTRICAL SPECIFICATIONSINSTALLED SIZEWEIGHTWEIGHT w/WATERGAL. TO OVERFLOWMIN. OPERATING GAL. BATHING WELL AT SUMPBATHING WELL AT RIMWATER DEPTH TO OVERFLOWFLOOR LOADING(PROJECTED AREA) PTS. CUBE (FT3) 2.1 HPR, 13.5 AMPS, 120V.PUMP34" (864mm) 59-3/4" (1518mm) 59-3/4" (1518mm) 60-1/2" (1537mm) 45-1/2" (1156mm) 84-1/2" (2146mm) 22-1/4" (565mm)12-5/8(321mm) PUMPLOCATION27-1/2" (699mm) PUMPLOCATION72" (1829mm) 36" (914mm) 10" (254mm) 6" (152mm) 15-3/4" (400mm) 21" (533mm) 72" (1829mm) 42" (1067mm) PUMPLOCATION36" (914mm) 72" (1829mm) PUMPLOCATION54" (1372mm) 27" (686mm) INSTALLATION AND FRAMING INSTRUCTIONSThe variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as needed. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used as the primary access opening. TYPICAL PIER TYPE INSTALLATIONAS DESIREDFCUTOUTAS DESIREDGCUTOUTC 4( 10 mm) 1 ( 05 mm) MOUNTING SURFACEWATERPROOF SEALANTBATHTYPICAL RECESS INSTALLATION 4( 10 mm) 1 ( 05 mm) CEDWLEVELINGSTRINGERSTILETILEBEADSTRIPLEVELING STRINGER 1 x 4 (not for support) BATHADHESIVESEALANTWALLBOARDNOTE: Tile bead kit not included and must be purchased separately. CTYPICAL INSTALLATIONFIGURE 1 Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base consisting of cement, mortar, or grout will help provide a solid and secure installation. . Install drain components to the whirlpool following the drain installation instructions. Before replacing your whirlpool for final installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing and Table 1 for suggested opening size (shadowed) and location dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to Table 1 under total weight for your model. . Remove the whirlpool and attach a 1 x 4 stringer to the studs, with the top of the stringer touching the traced line. The rim of the bath must not support weight. 1. Position the whirlpool into the installation opening and level the deck in both directions, shimming the integral support feet IF necessary. Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1). ! ! ! ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. FOR E & D DIMENSIONS SEE TABLE 1 ON PAGE 5.FOR G & F DIMENSIONS SEE TABLE 1 ON PAGE 5. NOTE: FRONT EDGE OF BATH MUST BE SUPPORTED BY STUD WALL OR AMERICAN STANDARD APRON KIT The rim of the bath must not support weight. If foundation base is used, allow the bedding material to completely harden before applying...

Baixe o seu

Para fazer o download, introduza 2 dígitos :