CANCEL REPORT? If you decide to delete the job, press 4 (–) for YES. • To cancel deleting the job, press e (+) for NOTE NO. Once the job is deleted, it is impossible to restore the job again. Chapter 7 Maintenance Periodic Cleaning Your machine requires little periodic maintenance. This section describes the necessary cleaning procedures for your machine. • When cleaning the machine’s exterior or the platen glass, be sure to disconnect the power cord CAUTION before cleaning the machine. • Do not use tissue paper, paper towels, or similar materials for cleaning; they can stick to the components or generate static charges. Use a soft cloth to avoid scratching the components. • Never use volatile liquids such as thinner, benzene, acetone, or any other chemical cleaner to clean the interior of the machine; these can damage the machine’s components. Cleaning the Exterior Wipe the machine’s exterior with a clean, soft, lint-free cloth moistened with water or diluted dishwashing detergent solution. 7 Cleaning the Scanning Area Wipe the scanning area (shaded areas) with a clean, soft, lint-free cloth moistened with water, then wipe with a clean, soft, dry, lint-free cloth. Maintenance Platen Glass Cover Platen Glass Cleaning the Read Area of the Platen Glass (Only for the imageCLASS D340 model) Black lines may appear in copies when the ADF is used to feed documents. This can be caused by glue, ink, correction fluid, or other foreign matters in the read area of the platen glass (shaded area). Use a clean soft cloth to wipe the read area clean. Take particular care to clean the locations where the black lines are appearing on copies. If you have trouble getting the glass clean, wipe with a cloth moistened with water or a mild neutral detergent, and then wipe the glass dry with another cloth. Read area Glue, ink, correction fluid, etc. Black lines Copy • Glue, ink, correction fluid, and other foreign matter can soil the platen glass when you copy a document through the ADF while the glue, ink, or correction fluid on the original is still wet. This can cause black lines on copies. When you load a document in the ADF, always check to make sure that any glue, ink, or correction fluid on the document is completely dry. IMPORTANT When to Replace the Cartridge When to Replace the Cartridge The cartridge is a consumable item needs to be replaced when the toner runs out. The following guidelines will help you to determine when to replace the cartridge. If white streaks or light bands are still presentIf the copies appear normal Remove the cartridge from the machine. Always hold the cartridge as shown so that the side with the written instructions facing upward. Do not forcefully move or push the protective shutter of the drum in any way. Rock the cartridge 5 or 6 times to distribute the toner evenly. Re-install the cartridge in the machine. Then, make a few test copies. If white streaks or light bands are displayed on copies, the toner in the cartridge is running low. You can use the cartridge, however, a new one will be needed soon. Replace the cartridge with a new one. (> p. 7-6) Paper Feeding Direction Instructions 7 Maintenance Copy Yield This section describes the approximate number of copies that can be made per cartridge. Approximate Copy Yield Canon S35 Cartridge : approx. 3500 copies (A4 at 5% dot coverage*). * The term “A4 at 5% dot coverage” denotes an original on which the area covered with black ink is 5% of the total area of an A4-size sheet. • The actual number of copies that can be made per cartridge depends in part on the copy exposure setting, room temperature and humidity. • If you copy a large number of originals which contain heavy print or many photographs, toner consumption will increase, and white streaks will appear on copies sooner than indicated above. Toner consumption will also increase if you copy with the platen glass cover left open. • Small-sized originals and originals with less print will use less toner. However, although you may be able to use the cartridge longer than indicated above, dark bands might appear on copies. Handling and Storing the Cartridge This section describes the precautions to ensure optimum copy quality. Handling Precautions • Do not throw cartridge into open flames, as this may cause the toner to ignite and result in burns WARNING or a fire. • The cartridge emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities, please move away from the cartridge, and consult your doctor. IMPORTANT • Never attempt to disassemble the cartridge or open the protective shutter of the drum. • If the machine is brought from the cold outdoors into a warm room, or if the room is rapidly heated, NOTE condensation may form inside the machine. This can adversely effect the quality of your copy images (e.g., copies are completely black). When the machine is exposed to such conditions, allow at least two hours for the machine to adjust to room temperature bef...
)
Log: