Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Attach tip-over bracket to compactor with one slotted head screw on each side. • Remove the compactor drawer for easier handling. • Then position the compactor just in front of the cabinet opening. • PLUG POWER CORD INTO THE WALL RECEPTACLE. • Slide compactor back into cabinet opening. Note: Make certain that the leveling feet caps are on the leveling feet and the power cable is not under compactor. The short leg of anti-tip bracket should be completely under the lip of the countertop but not so far back that the screws can’t be put in. If the bracket is not in the proper location, pull the compactor back out far enough to get to the top screws and reposition the bracket to the appropriate hole. Drill (4) 1/8" dia. x 1/2" deep pilot holes in the underside of the countertop at the location of the four holes in the short leg of the anti-tip bracket. Caution: Do not drill up through the top of the countertop. Secure anti-tip bracket to countertop with 4 Phillips head screws (supplied) on each side. Compactor Top Countertop Overlap Installation Built-In Compactors Step 5 If the countertop cannot be drilled into, slip the 90° (continued) clips over the short leg of the bracket and screw into the face of the cabinet. Step 6 Optional custom toekick To install custom toekick (not supplied) measure the front of the compactor’s adjustable base and use those dimensions to cut out your custom toekick. Secure as appropriate to installation. Note: The custom toekick should be installed in such a manner that it can be removed if service is required. Installation Built-In Compactors Step 7 Remove compactor drawer by pulling it out until it Changing stops. Then lift the drawer to clear second stop andfront panel remove drawer. Place drawer on its back. (ZCG3300 and 3100 only) Procedure A Reverse color panel Remove the two screws in the bottom edge of the trim. Slide panel out, turn it over and slide back in. Reinstall trim. Optional Procedure B custom 1/4" thick wood panelpanels Proceed as in “A” above, but discard the aluminum (ZCG3300 and color panel and cardboard spacer. Slide 1/4" panel 3100 only) into trim. Reinstall trim. Procedure C 3/4" thick wood panel with supplied handle • Pull the drawer out to stop position. • Unlatch the drawer front by opening the clasp on the right side. • While supporting the weight of the drawer front, remove the hinge pins on the left side. Installation Built-In Compactors Procedure C (continued) • Lay drawer front face down on a flat surface. • Remove 9 screws which retain the front panel and handle. – Save handle and galvanized inner door. – Discard front panel with side trim. • Place galvanized inner door onto the back side of the finished panel. • Position the inner door 1/4" below the top of the finished panel and center, left to right. • Use the inner door as a template. Drill 3 pilot holes in the top edge and 2 at the bottom, sized to match screws being used. (Screws are not provided) Caution: Select screw length carefully to avoid penetration of the finished side. • Lift the top edge of the inner door and slide the handle between the inner door and the finished panel. Align the screw holes of the inner door and handle with pilot holes. • Drive 2 screws loosely in the top. Align bottom holes, and check to be sure that the inner door is centered left to right over the finished panel. Drive 2 screws at bottom. • Drive last screw at top, tighten all screws. • Replace drawer front to drawer by re-installing the hinge pins. Swing door against drawer and secure with side clasp. • Slowly push the drawer closed and check alignment of the panel. Installation Built-In Compactors Procedure D 3/4" thick wood panel with custom handle • Pull the drawer out to stop position. • Unlatch the drawer front by opening the clasp on the right side. • While supporting the weight of the drawer front, remove the hinge pins on the left side. • Lay drawer front face down on a flat surface. • Remove 9 screws which retain the front panel and handle. – Save galvanized inner door. – Discard front panel with side trim and handle. • Place galvanized inner door onto the back side of the finished panel. • Position the inner door 1-5/16" below the top of the finished panel and center, left to right. Back Side Finished Panel CL 1-5/16" Galvanized Inner Door • Use the inner door as a template. Drill 2 pilot holes near the top and 2 at the bottom, sized to match screws being used. (Screws are not provided) • Drive 2 screws loosely into the bottom and 2 screw into the top. Check to be sure the inner door is centered left to right over the finished panel. Tighten screws. Caution: Select screw length carefully to avoid penetration of the finished side. Galvanized Inner Door Back Side Finished Panel CL Installation Built-In Compactors Procedure D (continued) • Turn the panel over, appearance side up. Use wood blocks to support the inner door and prevent damage to the hinge and lock tabs. • Drill pilot holes through the front...
Este manual também é adequado para os modelos :Outros aparelhos de cozinha - MONOGRAM ZCG3300 (286.92 kb)
Outros aparelhos de cozinha - MONOGRAM ZCG3500 (286.92 kb)