Assessments - 1, GPA: 5 ( )

Fabricante : GE Arquivo Tamanho: 466.78 kb Arquivo Nome : Língua de Ensino:

If your power supply does not include a ground wire, you must provide one unless metal cable is used. Attach a copper wire securely to disposer ground screw and attach other end of wire to the nearest grounded connection. Use only UL approved ground clamp. If plastic pipe is used in your home, a qualified electrician should install a proper ground. Most houses have electrical outlets under the sink that are half- hot. This means one outlet is controlled by the wall switch, while the other is always hot. The batch-feed or “TC” model connects to the hot side, while the continuous feed model connects to the switch side. 1. Attach a power cord, minimum 18. in length and not to exceed 36. in length. GE Kit #PM3X115 provides the parts needed to make this connection. or 2. Wire the disposer directly into the house current. GE recommends that a qualified electrician make this connection. To Attach a Power Cord: GROUNDING INSTRUCTIONS: This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The power cord (to be installed) must have an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. In the absence of local codes and/or ordinances, the outlet must comply with NEC requirements. DANGER: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. NOTE: Disconnect electric power to disposer circuit before installation. Turn the circuit breaker to the OFF position or remove the fuse. A. Connect the disposer to 110–120 Volt, 60 Hz AC current only. B. If a plug-in cord is used, use a three-prong plug. Ground wire should be attached to the ground screw in the bottom of the disposer (end bell). Trace lead connected to this Ribbed blade and attach that lead Side to white wire on disposer. NOTE: When viewing face of electrical plug with grounding pin at top, the larger left blade is connected to the identified wire. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 3 Installation Instructions Disposer If you have questions, call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • Skill level – Installation of this appliance requires basic mechanical skills. • Completion time – 1 hour • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. ADDITIONAL MATERIALS YOU MAY NEED • Steel punch or wooden dowel • Petroleum jelly or liquid soap • Hose clamp • Dishwasher drain connector • Adjustable pipe wrench • Plumber’s putty (for cast sinks) • Stepped rubber drain adapter • Wire nuts • Cable connector • Flexible drain pipe • Power cord kit (Part Number PM3X215GDS) WHAT YOU WILL NEED • Phillips and flat blade screwdrivers • Channel lock pliers, slip joint • Hammer • Nut driver PREPARATION 1. Disconnect electrical power supply to disposer. 2. Remove old disposer or sink flange assembly. 3. Inspect drain line. If it is heavily coated with hardened grease and accumulations, rout out with a plumber’s snake. 4. Remove old sealing materials and gasketing from sink opening, both top and bottom. NOTE: Top and bottom of sink surfaces must be free of any materials to prevent leaks. Installation Instructions COMPONENTS AND INSTALLATION 1 COMPONENTS INSTALLATION OF SINK FLANGE (Read completely before starting.) Sink Flange Rubber Gasket SinkFiber Gasket Support Ring Open Area No Obstruction Sink Flange Mount Ring should be free to move up and down *Stopper *Removable Splash Guard Sink Flange Rubber Sink Flange Gasket Groove Dishwasher Discharge Inlet Elbo...

Baixe o seu

Para fazer o download, introduza 2 dígitos :