1. Connect the ." dia. copper waterline to the ." flare water inlet fitting of the valve. 2. Plug the power cord into a proper receptacle. 3. Activate the Power Switch (Toggle Up). The red power indicator light and the green dispense buttons will light up and the tank will start filling. Allow approximately 4-5 minutes for the tank to fill. 4. Activate the Heater Switch. Allow approximately 10-30 minutes for the water to reach a temperature of 195°F. The heat up time will depend on the water inl

Clean or replace it. C) Dual Probe Test If lack of water persists, first check incoming water flow rate, if flow rate is OK proceed as follows: Turn on the power and water supply. Check inside the tank to make sure the water is below the Probe. Pull the BLUE wire and terminal OFF the Probe rod. If water still does not flow after the wire is disconnected from the Probe, the problem may be in the Solid State Dual Level Control Board. If water starts flowing into the tank, the Probe may be grounded

2 • Installation and Operating Instructions.............. 4 • Adjustments......................................................... 6 • Programming Instructions................................. 8 • Care and Maintenance........................................ 8 • Trouble Shooting Guide..................................... 11 • Parts Identification.......................................…... 15 • Wiring Diagrams................................................ 21 Cecilware sells value... Worldwide 45

OptionsForThisSeriesPortion Control SMARTSENSEHot Water Dispense Electrical*SuperSKImodelsonly.**AvailableonlyonGB1SKI-LD, GB2SKI-LD&GB2SuperSKI-BL-LDmodels. Stainless Drip Tray Slanted Whipper Chamber Hot Water Dispense OOOIOOIProgrammableButtonsAdditionalFeaturesForThisSeries*** Vending & Pour-Over Models • 3 Flavor S S ell Cappuccino 24 hours a day. . . 365 days a year with Cecilware’s vending model. Don’t let a lack of water lines stand in the way of selling cappuccino. Cecilware has the ans

AdditionalFeaturesForThisSeriesStainless Drip Tray Portion Control SMARTSENSEHot Water Dispense ElectricalSKIWhipperPortioncontroladd“PC”sufUx.Smartsenseadd“SMT” sufUx.Hotwaterdispensebuttonadd“W”before“LD”sufUx. Electricaloptionsavailable. Plumbing:."Waterlinerequired.Electrical:120/240V,6KW,25Astd. ExportVoltage:220available. SKIWhipperSeries•1&2FlavorOptionsForThisSeriesWhenItcomestodispensinginvolume…ProUtfromtheexperts.SingleVavorcontinuousextraheavyvolumedispensers. AdditionalFeaturesForTh

Avenue, LIC NY 11105 ®Tel: 800.935.2211 / 718.932.1414 • Fax: 718.932.7860 Since 1911 CecilwareHotBeverageDispensersStandardFeaturesIncludedOnAllDispensers* Fast Flow VSRSMoisture&Powder Collection Tray Direct Drive Power Whip Self Cleaning Quick Change Transparency •FastFlow–Dispensesbeverages30%faster,reducingwear&tearonmajordispensercomponents. •VacuumSteamRemovalSystemVSRS–Ensuresthepowderedmixremainsdrytoeliminateclogging,cakingandbridging. •Moisture&PowderCollectionTray–Preventsexcessmoist

** Except GB3M-10-LD. Options For This Series Hot Water Portion Control SMARTSENSEDispense Electrical Portion control add “PC” sufUx. Smartsense add “SMT” sufUx. Hot water dispense button add “W” before “LD” sufUx. Electrical options available. Model GB3M-GB3M-GB5M-GB5M- 10-LD 10-LD-U 10-LD 210-LD-U # of Hoppers 3 3 5 5 Hopper (1) 10 lbs. (1) 10 lbs. (1) 10 lbs. (2) 10 lbs. Capacity (2) 5 lbs. (2) 5 lbs. (4) 5 lbs. (3) 5 lbs. Width 11." 11." 18" 20" Depth 22" 22" 22" 22" Height 34" 34" 34" 34" T

C Dual Probe Liquid Level Controller malfunction. Check Controller. Replace if necessary. A Heater Switch is OFF. Turn Heater Switch ON. B Thermostat is OFF. Turn Thermostat ON. C Loose connection on Thermostat. Make sure all wires and terminals on Thermostat are tight. D Hi-Limit Temperature Switch is defective Replace the Hi-limit switch. 7 Water is not heating up in water tank. E Heater is burned out or defective. Replace the Heater. Model L690A (Rev. B) Dual Probe Liquid Level Controller Ove

3. HEATER SWITCHES. See diagrams inside this manual for the location of heater switches for each individual model. Their primary function is to shut off the heating elements during the initial priming, start up operation of the machine, or whenever the tank is being drained for service. 4. POWER SWITCHES. See diagrams inside this manual for the location of power switches for each individual model. They control all power to the unit including the heater elements. Note: The Power and Heater Switch

Model #: Serial #: Voltage: Date of Purchase: Business 8:30 a.m. to 5:00 p.m. Hours: Eastern Standard Time Telephone: 800-935-2211; 718-932-1414 Fax: 718-932-7860 Additional information can be found by visiting our web site at INTRODUCTION The Cecilware 5, 6, & 8 head instant Cappuccino Dispenser is designed to meet the exact needs of the Convenience Store atmosphere. Cecilware has led the way in the highly profitable and growing market of Cappuccino with its GB series of Automatic Cappuccino Di